PDA

View Full Version : 1988 Honda Accord LXi turns over but not starting


cjpriceless
Feb 12, 2005, 05:28 PM
Hi there,
I have a 5-speed 1988 Honda Accord LXi with pretty high miles, but has been running great for the 8 or so months I've owned it. However, yesterday when I was driving to town it stalled at the stop sign. This stall was kind of out of the blue, because I did not let out the clutch too fast or anything. Then when I tried starting it there was this low pitched thud sound as it kind of started... it did this about two or three times, and then when my friend and I pushed my car back out of the road it stopped doing the thud when I tried to start it, and instead it would just turn over and not start. I have plenty of gas, and I added more oil yesterday after all of this happened. The belts seem to all spin when you turn the key. My main thought is that it is the timing belt, since I'm not really sure when it was last replaced and those are notorious for going on on Hondas after a bit. The other thought I had was that maybe it is the spark plugs, since it seems that it turns over just fine, just doesn't get that spark. But that wouldn't really explain the thud sounds before when I tried to start it. I really need someone's help on this one... I'm kind of low on cash and need to get this car back in service without spending a fortune.
Thanks,

Casey

labman
Feb 12, 2005, 06:28 PM
Does it have a distributor? You may need a helper. Pull the cap off, and one of you watch the distributor insides while the other cranks. If the rotor doesn't turn, the timing belt is broke, sorry. If it does turn, while you have the cap off, clean the contacts, and inspect the center one. Then work your way from the spark plug wires back to the ignition key, trying to see where you don't have the voltage you should. Let me know what you find. I am not real familiar with Hondas, and will need help on how yours should work.

thebriggsdude
Feb 12, 2005, 07:07 PM
Yeah it sounds like the belt broke :(

cjpriceless
Feb 12, 2005, 07:11 PM
Any idea where the distributor is in this model? I'm not too familiar with stuff under the hood, so I'm just going by what I find in the manual and such. Thanks.

thebriggsdude
Feb 12, 2005, 07:53 PM
Well it depends on the engine, not familiar with hondas but if it's a frontwheel drive side installed engine some will be on the front towards the front of the car or on the back opposite the pulleys and belts, if it's a rear wheel drive, most likely in the back, you'll probably have to remove some engine cover to see it since newer auto's are all covered up engine wise, sad thing I know I hate them when they're covered :(

labman
Feb 12, 2005, 07:55 PM
I would think an 88 would have a distributor. Most newer cars don't. If you have spark plug wires, follow them to where they come from. If it is an oblong box, it doesn't have a distributor. If it is sort of round or multisided, that is the distributor. It should have 2 clips or screws that hold the cap on. Remove them and you should be able to pull the cap off. Inside it should have a contact on top that turns from one wire to another. It is driven by the cam, and should turn when the engine does.

cjpriceless
Feb 12, 2005, 08:54 PM
Well, I traced the cables back which was pretty easy... because they or only around 2 feet long. The go to this weird shaped metal thing on the opposite side of the engine than those of the pulleys and belts. I looked at it to see if it is removable, and I'm sure it is somehow, but it wasn't very straightforward. Does this sound like it could be the distributor? How big is this thing supposed to be? And also, is there any other way to find out if it's the timing belt besides removing anything? Thanks.

labman
Feb 12, 2005, 09:20 PM
Distributor caps are plastic not metal, maybe hard shiny, black plastic. There will be fingers that stick up in a circle with the wires coming out of them. A metal box likely is just a coil housing. Some cars have an inspection port for the belt. It will be at the end of the engine with any other belts, not the transmission end. We need help from some of the other Honda owners here to describe it. Is the oil filler in the valve cover? Take the cap off, and you may be able to see some of the valve gear or the cam itself. Again, one watch while the other turns the engine over. If you see any movement, the belt is OK. Valve covers are either stamped steel, or cast aluminum. There may be 2 with the spark plug wires going down between them. A valve cover may not be too bad to take off. You will be able to see the valve stems inside their springs as well as the cam shaft itself. Again, turn the engine over ahd hope to see movement. The valve cover will need a new gasket and be careful no to tighten up the bolts too much putting it back on.

CroCivic91
Feb 13, 2005, 01:28 PM
Labman said it right, a distributor cap is a black plastic thing that your spark plug wires connect to. On a Civic '90, you have to undo 3 bolts to remove the cap, one is on the upper left side, one on the middle right, and one is just under. If you have problems reaching the 3rd bolt, you might have to remove the battery (if it's in the way, I know it IS in the way on a Civic '90).

thebriggsdude
Feb 13, 2005, 01:31 PM
Yeah they are all plastic and held on by very few bolts. The distributor is just that your distributor driven by a belt or direct driven from the engine and distributes spark to every plug at the right time the piston comes up to compress and when the distributor screwed, you are in that fact of the matter. :D

cjpriceless
Feb 13, 2005, 02:38 PM
Ok so I'm pretty sure I found what you guys are talking about. It has the 4 spark plug wires running back to it and it is plastic. It is bolted to a metal base with two small bolts. So am I safe to unbolt these two things, or am I going to break a seal or something?

thebriggsdude
Feb 13, 2005, 03:36 PM
Most of the time they use maybe a rubber seal, should not hurt to open it but don't loose anything, you'll be hating yourself later if you do. :o

cjpriceless
Feb 13, 2005, 03:50 PM
Ok good and bad news... got that off, one of the screws was stipped but fortunately it was a hex screw do I used a socket wrench to get it off. Anyhow, my mom tried to start my car while I watched that part, and the rotor or whatever is inside of this did spin. So that would mean that it in fact is not the timing belt, right? And if it isn't that, what else could it be? The alternator has recently been replaced and it seems to have a good charge and not be running out of power. Just not getting through though. Thanks.

thebriggsdude
Feb 13, 2005, 06:37 PM
Does the plugs fire off a spark, hold them with rubber handled pliers or either lay them on a plastic surface, no metal or your hands now. If they fire then it may be something else. Maybe fuel delivery. If they don't the distributor may need rebuilding or the points cleaned or replaced. And also if the plugs are of some age and I mean old they may need replacing as well and the wires if they are old and cracked. Or could be the engine's off timing forgot that :o

labman
Feb 13, 2005, 08:35 PM
Great, I am glad to hear the distributor is turning. Timing belts are expensive, and sometimes other parts of the engine are damaged. Now it is on to spark and gas. Easiest thing is to pull a wire off a spark plug and crank the engine over with the end near something grounded. You may need to pull the boot back or put something metal in it so the spark doesn't have more than 1/4 inch to jump. It needs to be a nice blue spark. If no spark there, try the end of the cable in the middle of the distributor. If no spark, follow it back to the coil. Check for 12 volts at the small wires on the coil. If no power there with the key on, 6 volts may be OK, work your way back to the ignition switch. There is a relay under the dash that is troublesome on some Hondas.

If you have spark, then check for gas. Carburetors are easier. Remove the air cleaner, and work the throttle with your hand. If you see gas squirt in, the gas is OK. You may have to push open a plate to see very far into the carburetor. It is the choke plate. If it doesn't want to close when the engine is cold, that could be the problem. Try working it with your hand and see if it wants to stay closed then.

With fuel injection, you must remove a fuel injector, maybe the whole rail with multiport. Point it away from the car, your eyes, and any thing hot or electrical, and have someone crank the car. Gas should squirt out. I said be careful where your point it. No gas, look at the fuel pump, fuses, etc. Also recheck the relay under the dash.

Let us know what you find.

cjpriceless
Feb 13, 2005, 09:40 PM
I have not had a chance to try out any of this yet, because it is now too dark and cold out to do much of anything at all. I really appreciate the tips though. So with the spark plug stuff... do I just pull off the wire running to the plug and try to start the car and see if there is a spark? Also, what would explain the thud and weird noises when it first broke down? Thanks.

thebriggsdude
Feb 13, 2005, 10:40 PM
Umm well you take the plug out and leave it connected with the wire, thud, oops forgot that ooooooooooooh :o that would be a lot of things, was it a bump kind of thud or a clank kind of thud :( most of the time if it was a clank that means something big. :( check for spark and if you have a automotive compression preassure tester test each cylinder if it was a clank thud and check the oil for metal shavings, if it was a bump well it could have been just the engine rocking back and fourth and knocked a connection loose. Thuds will mean lots of things.

cjpriceless
Feb 13, 2005, 10:54 PM
Ok I'll give that a try tomorrow. The thud was a low pitched sound, kind of like if you were shifting from first to second and accidentally put it in fourth, and so the engine sound was were low pitched opposed to its normal mid-high pitched sound. Not really a clang sound though, more of a bump type. Any idea of what else might have caused this? It doesn't seem like it would be electrical shorting, just because of the nature of the weird thud sound. And I'm thinking its not an issue with fuel, because if I get the gas a few pumps before starting then when you go back to the hood you can smell the gas, and it turns over just fine.

thebriggsdude
Feb 13, 2005, 11:22 PM
Umm you really shouldn't be able to smell the gas, that bump may have been a rock or something knocking a fuel line or something aloose and stalled the engine. Even on my carbe'd car I smell little to no gas. You might have a fuel line cut, ruptured, or either popped off, I'd suggest checking to see if the injectors get fuel before you try the plugs. If you smell fuel then it's the fuel. That would explain the thud and the gas smell and stalling. :( do not if its leaking gas, you might should try starting it while you look under the car for gas squirting and then leave it alone if you do. Get it towed or fixed right there. You don't want a really bad thing to happen now with gas. If it was me I would be able to fix it but for you if its leaking fuel your best bet is to get a pro to do it. Check the fuel first though, if you smell fuel that would make me look at the lines or either under it and see while starting it. Check like labman said the fuel rail if equipped or the fuel injectors and throttle body if throttle body injected. Is the fuel smell really pungent and noticeable or is it not hardly at all. If its noticeable while the hoods down and all shut up fuel problem. I would highly suggest all of the above.

CroCivic91
Feb 14, 2005, 05:14 AM
The underdash relay labman was talking about is a Main Relay. The problem that relay cab cause is when you try to start the car in a hot day, or just after you turned the engine off, the engine won't start, or will start but will immediately stop. The way you fix it is like this: you locate the relay (it took me 1 hour to locate it actually), take it out (another 1 hour of work, it's in an extremely inaccessible location), open it up, resolder all the joints (that was the easiest part) and put it back in (it was actually easier putting it back in than it was taking it out). Now where do you find the relay? It is under the dash, behind the coin tray (which is by your left knee when you sit in the car), above the thing you pull to pop your hood. You have to unbolt the 3 bolts on the coin tray and remove the coin tray. You will be able to see about 20-25% of the main relay when you do that. It is a black box with Mitsub-something written on it (it says Main Relay on it too). It holds to this metal piece with one bolt, which you undo and disconnect the wiring harness from it, and pull the relay out.

Well, if you have problems starting the car in the summer, you could do it, and it might help you with this too.

labman
Feb 14, 2005, 08:36 AM
Some smell of gas is a clue to the problem, and nothing to be too excited about. It likely means either a lack of spark, or a leaky injector. You don't need to remove the plug to check the spark, just the wire and let it lay near a ground.

If you crank the car with the injector removed, gas should quit flowing as soon as the cranking stops. If it continues to dribble out, the injector is leaking. Replace it.

Could the noise have been a backfire? Sometimes they are more like a cough than a gunshot.

thebriggsdude
Feb 14, 2005, 09:19 AM
Yeah on those a backfire could be a burp rather then a boom. But yeah leaks are very much possible if you smell gas and if it does not start. But I did encounter a problem one time with a fuel injected car where he had hit something and knocked a gasline off. Not saying yours but gas smells lead me to the gas. Woops forgot to add, the reason why I said remove the plugs to check while connected to the wires. It will tell you if your getting spark and will tell you if the plug is bad, plus old wire's will be cracked and you reallllllllllllllllllyyyyyyyyyyy don't want to touch them, realllllllllllllllllllllyyyyyyy :eek: :eek: shock of your lifetime :D

cjpriceless
Feb 14, 2005, 06:12 PM
Ok this smell of gas isn't that much... just a faint smell, I guess something to be expected if you've pumped it quite a few times over a few tries of trying to starrt it. I also checked all of my key fuses and nothing is blown. I'm not really sure about this relay thing though... is that just where all the fuses plug in behind the coin holder, or somewhere else? I checked the connections of the wires running to the plugs, and the cable running from there to the coil and there is no corrosion and it is a clean plug. I also tried unplugging a wire from a spark plug, sticking the screw driver in the cable to make a metal connection, and then touching it to a metal ground while someone turned the car over... but there were no sparks or anything. So anything else you guys can think of? I also think my battery is getting close to dying from all of this trying, because it doesn't seem to turn over quite as well as it was the other day. One other note... I tried jumping it today just for kicks and that yielded no results either. Thanks.

thebriggsdude
Feb 14, 2005, 06:49 PM
Well the plug wire is not to be touching metal more like having a piece of metel say the side if the engine a little bit away to spark, that's why I said take the plug out, the wire is not to touch metal but to be emitting a spark to the metal if touching you would get no spark because it would be grounding. Yet hold the end of the wire with the screw driver in it and keep it away from a metal contact, maybe a cm or even a half of a cm away to spark to the metal. Clean metal as well, like a clean non painted alluminum/ steel / iron engine head. :)

cjpriceless
Feb 14, 2005, 08:20 PM
Yeah no luck with the spark... right now I'm trickle charging the battery because it was getting a little low.

thebriggsdude
Feb 14, 2005, 09:15 PM
Well I'd hate to say this because it will hurt and give you a buzz if it does give spark energy, touch the screwdriver while its in the plug connector with the back of one of your fingers and try to start it, if you get a jolt well OK its getting some. But I would keep trying the other way :D , umm well here's a question, OK where was this thump thud etc. it might, now not saying but might have disconnected something under the dash. But if you try a spark tester which you could rent at auto zone I believe not sure or use a electricians electrical voltage tester/ meter and see if you get something, cheapest way would be above. :D but not recommended. Or could be the belt slipped, not sure what type belt now I'm used to timing chains, could have slipped if it's a belt, not sure on these japanese cars but could have slipped. Like I said try taking the plugs out and leaving them connected to the wires and try to start the car and look for spark and see if you get it in all of them and they are all sparking one after another or in sequence if the starter turns the engine over fast. May have been a computer chip has fried, had that happen to a caprice one time, got fuel and through the injectors and turned over but no spark and the computer was screwy, not saying that yours is though, damn this ones kind of a screwy car, seen one honda crx hatchback going at 60 for 5 minutes and the power steering would go dead. Just screwy stuff, try the plugs though :)

cjpriceless
Feb 14, 2005, 10:10 PM
Alrighty thanks I appreciate it. I also talked with a mechanic friend and they think it might be fuel, so they said to take a tablespoon of gas and put it in the air cleaner/carburator and see if that starts it up... he said that it sounds like it might be the fuel pump. Which I guess logically sounds reasonable. Anyhow I'll give all of that stuff a try tomorrow. Once again thanks.

thebriggsdude
Feb 14, 2005, 10:21 PM
yeah like I said that thump could have been the pump

^^ I made a funny :D

. Do try the gas though but could be it isn't that since you smell it

cjpriceless
Feb 15, 2005, 07:58 PM
Well my dad and I weren't able to figure it out... it still seemed like there was no spark, and then its Electronically Fuel Injected so what didn't know what do to there. So tomorrow morning I'm hoping to get it towed into town with our Triple A and have a true mechanic take a look at it. I really hope I can get my car working very soon... having no car is a real pain in the .

thebriggsdude
Feb 15, 2005, 08:09 PM
Yeah would be your best bet since. I need the car right there to really tell what's wrong, but hope its not serious :(

cjpriceless
Feb 16, 2005, 07:54 PM
I hate car mechanics... they tell you that you can have your car towed in, but that they won't be able to get to it until Friday... what is the deal with that. Once Friday rolls around I will have been without my car for a week, and I really am starting to need it. Especially since next week is Mid-winter break.

thebriggsdude
Feb 16, 2005, 08:19 PM
I know it sux sometimes. But be leanient, sometimes they can be over full with things already to do, plus about all of them leave the big things till last and do the small things.

cjpriceless
Feb 18, 2005, 07:58 PM
Well one of my good friends told me of this Mobile mechanic they knew of and that had helped them in the past. So I gave them a call and they came out today. They have the cheapest rates around here and seemed to be pretty nice people... in the first hour check-through they didn't find anything wrong. All of the standard tests had passed and everything seemed pretty OK, then they called me and asked if it was all right if they did a diagnostics test. So they went through with that and found the problem. Evidently something between the distributor and coal was grounded and had shorted out and died or something, and then burned out some of the wires. So they took the distributor or distributor cap (are these two the same or different?), and told me that this part that needed replacement is a $391 part. So I guess overall it is going to cost about $530. Does this seem reasonable, or does it sound like I might be getting ripped off on that part? Thanks. I'm thinking it might be the ignition distributor... but not totally sure.

labman
Feb 18, 2005, 08:35 PM
That sounds absurdly high, but it is possible that it is a fair price for a factory part purchased from the dealer. It seems everything is more complicated today, making it more expensive. Then if a mechanic buys a factory part from the dealer, and of course marks it up, it is expensive. Everybody that works on cars marks the parts up. The mechanic marks them up, the dealer marked it up, the factory marked it up, etc. You pay.

I am not sure what is in distributors today. They used to have a switch to make and break the circuit to trigger the spark, weights and a diaphragm to adjust the timing, plus the rotor to distribute the spark. They may have some electronics to replace those things plus still the rotor. My old truck still has the switch, called points. My last 2 cars didn't have a distributor.

I had to replace several wheel bearing on my old Grand Am. Can you buy just the wheel bearing? NO, you buy the whole hub complete with the ABS sensor. Maybe I had to go back and replace it again because I bought the cheap $100 ones.

thebriggsdude
Feb 18, 2005, 10:20 PM
Its kind of on the reasonable side since they have to nowa days to replace or work on those cars. Because yes they mark up the price but of course they have to install it, work on it and get it right as well.

CroCivic91
Feb 19, 2005, 05:41 AM
Distributor cap is only a part of a distributor. There are quite a few things inside. You should ask them which part of it exactly went wrong, and then visit www.cheapesthondaparts.com and look it up how much each part costs. I can tell you right away that for your car some prices are like this:
Whole distributor (Hitachi) - 472$
Whole distributor (Tec) - 437$
Ignition coil - 61$
Rotor (Hitachi) - 4$
Rotor (Tec) - 3$
Cap (Hitachi) - 14$
Cap (Tec) - 14$

There is also an ignition switch, but they don't have it in stock I guess, since they didn't show the price. But if they're saying 380$+, then I guess they're trying to replace the whole distributor. If it's only the coil or only the cap, just buy the part, you can replace it yourself (I know I replaced it myself (for the first time in my life) in 45 minutes).

jgrayii
Sep 18, 2009, 07:55 AM
If your car is fuel injected, this will help. Turn the ignition on slowly, listen for a click sound after 5 seconds. If no sound, then have your main relay replaced. Its located under the driver side fender behind the fuse box. This relay signals the fuel pump to send gas through the line, to the engine.

Had this problem recently with mine and once I made the installation, started like a rocket.

rnate
Oct 5, 2010, 02:35 PM
I would try shaving the head by 0.22 and it helps cause when u do that it makes the car 10 times faster and that help it happened to me