Hi. I have kenmore elite model 110.62992104 and it will no heat up. Also the drum will rotate whether the door is open or closed. I read somewhere that a defective door switch might also be the cause of no heat and would like to know if that is true. Also, where is the heating element located for this model.
Thanks in advance.

Most likely it is dirty and lint deposits have built up, as it always does, in all the air ducts which will cause the main safety to blow causing the problem you described.You need a multi-meter to find which safety has blown. You will have to take it all apart and clean the drier out thoroughly or it is all for nothing. Every air duct will have to be removed and scraped and washed out to remove baked on lint deposits which bakes on like a concrete lining. This will burn so the manufacturer has installed the safeties to keep from having a house fire. The safeties are oval-shaped with a round center part containing the safety with two plug-on terminals for the wires and when they burn open, from the dryer being dirty, nothing will work or it will not heat. Using an ohm meter you put a lead on each terminal of the safety, with one wire unplugged, and if it is good you will have a reading of about zero; if it is bad it will read infinity. On your dryer you may also have to test some thermistors if it has them. They are sensors that are around in different places to test the temperature and you test them with a meter set to ohms and compare the reading to a chart. They are specific to the dryer, but if you read nothing or a short you will know it is bad. Probably, once you clean it the dryer will run find after the blown safety is replaced, too. Driers were the number one cause of fires at one time, hence now we have safety fuses. Of course, you also have a bad door switch, if the meter bears that out. It could be something else, too. You will see the elements at the back of the dryer when you clean it. Look at: How to clean your clothes dryer. How to make it hot again. - YouTube (http://www.youtube.com/watch?v=MMP7BW1lLs4) to see how. Also look at these to get an idea about how to clean it: Mr. Appliance Tips: How to Clean Your Dryer - YouTube (http://www.youtube.com/watch?v=iBiRw-KElC4) ; Cleaning a Dryer Vent and Lint Trap - YouTube (http://www.youtube.com/watch?v=yFTZGgVisCI)
Electric Clothes Dryers (http://www.electrical-forensics.com/Dryer/ElectricClothesDryers.html) Dryer vent cleaning prevents fires - YouTube (http://www.youtube.com/watch?v=A6wmD502-xE) and: Cleaning out a dryer with top lint cleanout - YouTube (http://www.youtube.com/watch?v=OBNDbyRm68M&feature=fvsr)
Cleaning out a dryer: By a woman 2 of 2 - YouTube (http://www.youtube.com/watch?v=a73HTFkcB90&feature=relmfu)
When you finish cleaning the drier it is best to also replace the belt, too, because you do not want to have to disassemble it all over again and if the belt is over two years old you should replace it.

Note that on most of the videos it does not show them washing out the parts, but this is important because it's the only way to really get the parts clean, just don't get motor wet or the capacitor if it has one. Vacuum out the motor to remove all dust. I would move the drier out to your garage to have plenty of space to work. You also want to check your vent and clean it, also. The vent should have a short run and be straight as possible. The job is really easier than it sounds. There is no shortcut that will work; it has to be cleaned well. Before you re-assemble it make sure to use white lithium grease (high-temp grease) and grease all bearings. Here is a manual and parts list for one Kenmore dryer: (They are all about the same.) https://dl.dropboxusercontent.com/u/8010163/Kenmore%20Dryer%20Manuals.zip
Manuals: https://dl.dropboxusercontent.com/u/8010163/Kenmore%20Dryer%20Manuals.zip