PDA

View Full Version : How Do I Increase Frequency In 2.2KV Generator?


emmynet
Sep 26, 2013, 11:56 AM
I have a 2.2KVA (2.5KVA at Max) Electric Generator, within about 200 Hours of usage, I observed that the frequency droped to 25 (as indicated on the Hour Meter to read: F-25) from 60.

The Voltage remain costant as 230V, so please how do I increase the Frequency back to 60 as the Generator can no longer carry Fridge as when the Freqency was 60.

sinnadurai
Sep 26, 2013, 10:30 PM
Did you check the speed of the engine and AVR settings?

emmynet
Oct 1, 2013, 02:07 PM
Thanks for responding to my question.

Really I do not know to check or confirm the Speed, except through the audible noise from the generator that will denote that, it is running really fast. The LCD on the on the generator only display:

*Voltage
*Frequency
*Hours/Minutes of Usage
*Cumulative Hour of usage.

When I powered up the generator few hours ago, the generator was running low in speed (noticed via the sound), but the Voltage still remain 230V, I then noticed that the Frequency was 60Hz, but after running for a few minutes, the generator increased automatically in speed the frequency dropped to 26Hz!

After noticing the above, I then manually reduced the Running Speed of the Generator, to my surprise, the frequency promptly increased to 60Hz/65hz!

With the increase in the frequency, I observed that, the Fans in the House increased blowing/rotating speed too!

Kindly advice please, can I continue to use the generator in the manner? I mean, I hope it will not have negative effect on the generator or any house appliance.

Thanking you once again for your help.

sinnadurai
Oct 1, 2013, 11:17 PM
Use a tachometer(mechanical or electronic)

smoothy
Oct 2, 2013, 05:09 AM
This is a small portable Generator... I'm betting he's losnig one set of the poles on the generator head at times. Since most of these are 4 pole generator heads... losing 1/2 would drop your frequency in 1/2 and the reduced load might play a little havoc with the mechanical governor. (though it really shouldn't by much)

hfcarson
Oct 2, 2013, 09:13 AM
Have all the basic checks been done? Does this model have brushes?
Are all connections tight, inside and out?

emmynet
Oct 3, 2013, 02:41 AM
have all the basic checks been done? Does this model have brushes?
are all connections tight, inside and out?

Thanks for your respond.

Yes, the Model uses Brushes.

Regard,

Emmy.

hfcarson
Oct 3, 2013, 04:25 AM
Replacing the brushes may solve the problem...

sinnadurai
Oct 3, 2013, 06:06 AM
Non-contact type tachometers are available

emmynet
Oct 3, 2013, 01:08 PM
non-contact type tachometers are available

Thanks for the respond.

At the moment, am running the Generator with Frequency at 60Hz, that is, after I have reduced the engine speed by adjusting the Speed Control (on the Governor Control and also at the top of the Carburetor)!

With the Frequency at 60Hz, my refrigerator and Fans are now working fine. However, my fear is that, is that the best solution to this problem?

hfcarson
Oct 4, 2013, 04:33 AM
Best solution? That is yours to decide...
If you verified that the brushes are good and do not need to be replaced, that all connections are tight, all wiring is in good condition, then the generator may need to be replaced...
The next move is yours...

emmynet
Oct 4, 2013, 10:17 PM
best solution? That is yours to decide...
If you verified that the brushes are good and do not need to be replaced, that all connections are tight, all wiring is in good condition, then the generator may need to be replaced...
the next move is yours...

Thanks for the respone once again.

With the reduction in the engine speed that have given me the desire frequency rate of 60hz, has that not solve the problem? Or will it resolve to creating another problem in the near future?

Thankx.

hfcarson
Oct 7, 2013, 04:11 AM
Well let's see... so far you have done nothing...
So far all I have recommended is that you check the brushes...
Checking the brushes will cost about two minutes... if they are very short then sometime
Soon you will damage the generator.
If the brushes are good then the problem is elsewhere and we have narrowed the search and can then test or examine other possibilities...
What would you like to do?

emmynet
Oct 11, 2013, 03:00 PM
Thank you so much for your respond.

Yes, I have checked the brushes and find out that, the brushes are still long and good.

So, what next can I do please?

Thanks,

Emmy.