bgist
Jul 16, 2012, 08:19 AM
Good morning,
I am having a water problem and need some assistance determining how to fix it. I have a weekend cabin which has a well. When we had it drilled in 2004 it was 315 ft deep and we could hear a river underground when we listened at the entry point. We decided that since there was sufficient GPM production to stop and set pump rather than possibly going through the bottom of the river and drilling 300 more ft.
For the first 3-4 years it was fine except we put a hardness system on the line and a large carbon filter from Lowe's. Later we added a chlorination injection system.
Here is the issue now. Over the last year or so there has been a dramatic increase in the level of sediment in the water. We had it tested and the following are the numbers.
Hardness 16 gpg
Iron 9ppm
Ph 7.2
Manganese 0 ppm
Sulfur ppm (no number shown)
Tannins 0 ppm
Chloride 0 ppm
Sulfate (S04) 0 gpg
TDS 216 ppm
This was all tested prior to the in-line systems we have already.
Basically we have what appears to be clay in the water. It is a significant amount. The charcoal/filament filter that we currently have in-line is the biggest one Lowe's sells. It is approx.. 10” filter. It needs replacing after 5-10 days of use to avoid reduction in the water pressure.
We attempted to incorporate a sand filter in the system but used a swimming pool type filter which is designed for a maximum of 28 lbs of pressure. When we turn it on, if a faucet is open it works but when you close the system, the pressure pegs out the gage of the pool filter and it begins to creak from the pressure. It just isn’t designed for that pressure. I tried it in line prior to the pressure tank and after the pressure tank. Results were the same both ways.
1. What is the normal pressure in the pressure tank?
2. Am I doing something wrong or do I need a different type of tank rated for a higher pressure.
I am having a water problem and need some assistance determining how to fix it. I have a weekend cabin which has a well. When we had it drilled in 2004 it was 315 ft deep and we could hear a river underground when we listened at the entry point. We decided that since there was sufficient GPM production to stop and set pump rather than possibly going through the bottom of the river and drilling 300 more ft.
For the first 3-4 years it was fine except we put a hardness system on the line and a large carbon filter from Lowe's. Later we added a chlorination injection system.
Here is the issue now. Over the last year or so there has been a dramatic increase in the level of sediment in the water. We had it tested and the following are the numbers.
Hardness 16 gpg
Iron 9ppm
Ph 7.2
Manganese 0 ppm
Sulfur ppm (no number shown)
Tannins 0 ppm
Chloride 0 ppm
Sulfate (S04) 0 gpg
TDS 216 ppm
This was all tested prior to the in-line systems we have already.
Basically we have what appears to be clay in the water. It is a significant amount. The charcoal/filament filter that we currently have in-line is the biggest one Lowe's sells. It is approx.. 10” filter. It needs replacing after 5-10 days of use to avoid reduction in the water pressure.
We attempted to incorporate a sand filter in the system but used a swimming pool type filter which is designed for a maximum of 28 lbs of pressure. When we turn it on, if a faucet is open it works but when you close the system, the pressure pegs out the gage of the pool filter and it begins to creak from the pressure. It just isn’t designed for that pressure. I tried it in line prior to the pressure tank and after the pressure tank. Results were the same both ways.
1. What is the normal pressure in the pressure tank?
2. Am I doing something wrong or do I need a different type of tank rated for a higher pressure.