PDA

View Full Version : 93 honda accord fuel filter


chars54
Jun 8, 2012, 11:38 AM
On a 93 accord do you have to fill up the new fuel filter with gas before installing?

Stratmando
Jun 8, 2012, 01:19 PM
No.

chars54
Jun 8, 2012, 02:03 PM
My honda/over 300k mileage,will run for a few minutes and then losses gas pressure and sputters and quits... I put a new fuel filter on it (dry) and it ran great for a minute and did it again... hard to start again but when it finally does it runs fine then more of the same.. drianed 3 or 4 gal of gas from tank and its clear and good(no water).. Im sure its not the fuel pump and just wonder if its common for the fuel pressure regulator to fail and how does the regulator work with the vacuum.. is there a diaphram in it or what?. Dont really know how to check it or what to try next... Thanks...

Stratmando
Jun 8, 2012, 02:15 PM
How do you know it loses gas pressure? I would check Ignition Switch.

https://www.google.com/search?q=93+accord+ignition+problems&rls=com.microsoft:en-us:IE-Address&ie=UTF-8&oe=UTF-8&sourceid=ie7&rlz=1I7ADRA_enUS355#hl=en&gs_nf=1&gs_mss=93%20accord%20ignition%20switproblems&tok=cH_hTEXMz6rgf8UqdyxXrQ&pq=93%20accord%20ignition%20problems&cp=26&gs_id=s&xhr=t&q=93+accord+ignition+switch+problems&pf=p&rls=com.microsoft:en-us%3AIE-Address&rlz=1I7ADRA_enUS355&sclient=psy-ab&oq=93+accord+ignition+switch+problems&aq=f&aqi=&aql=&gs_l=&pbx=1&bav=on.2,or.r_gc.r_pw.r_qf.,cf.osb&fp=1af8e00401884db9&biw=1024&bih=640

TxGreaseMonkey
Jun 8, 2012, 02:25 PM
Replace the Ignition Control Module (ICM) and coil inside the distributor. Apply silicone heat transfer grease to the back of the new ICM. I have yet to see a bad Honda fuel pump or pressure regulator.

chars54
Jun 9, 2012, 02:26 PM
Replace the Ignition Control Module (ICM) and coil inside the distributor. Apply silicone heat transfer grease to the back of the new ICM. I have yet to see a bad Honda fuel pump or pressure regulator.well I got the coil out but while taking the icm out found that the small screws on the bottom.. the phillip heads are stripped out and I can't get it out.. also one of the wires on it looks like it has heat damage and may be part of the problem.. so how can I get to those screws... do I have to pull the distributor?

TxGreaseMonkey
Jun 9, 2012, 05:56 PM
Use a precision Phillips head #2 bit, such as from the omnipresent bit driver sets on the market. I often pull the distributor and set it down on my work bench. Just be sure to place an index mark on the distributor and mounting bracket, prior to removal. This will allow the timing to be very close when the distributor is reinstalled.

chars54
Jun 9, 2012, 08:20 PM
Use a precision Phillips head #2 bit, such as from the omnipresent bit driver sets on the market. I often pull the distributor and set it down on my work bench. Just be sure to place an index mark on the distributor and mounting bracket, prior to removal. This will allow the timing to be very close when the distributor is reinstalled.Hey Thanks for all your help... icm turned out to be bad with bad wires also.. Corroded and brittle... bad rotor and cap along with oil leak which keeps the belts drenched with oil... I think its time too put this car under the tree for a hobby later or sell it for parts... Time to buy me a pickup.. thanks again for your very accurate help, just glad now I didn't replace the fuel pump and or the regulator... I would recommend you to anyone...