I have a 3 yr old home with a fireplace that while poking wood we stabbed a crack in the back "fake brick" piece in the back. Now the crack is getting bigger. How do I fix this, is it a fire hazard?

I have a 3 yr old home with a fireplace that while poking wood we stabbed a crack in the back "fake brick" piece in the back. Now the crack is getting bigger. How do I fix this, is it a fire hazard?
What you have is probably a pre-fab fireplace. You will need to get the make and model number of the fireplace. Contact them and have them send you a new panel.

I have a prefab type fireplace to and have the same issue with a couple cracks in the firebrick. I would think that there would be some type of concrete type filler to repair this without dismantling the back of the fireplace that seems like a big job to do that, anyone have any other ideas?

Wiz has it right. Do not try to patch this panel with refractory cement, it will just keep cracking as the panel heats and cools. I have replaced panels before and it is remarkably easy. Majestic gave me a new panel at no chrage because I mentioned a hairline crack before it banged it larger with a poorly tossed log.

Thanks for the answer to my question. This fireplace is around 20 years old made by Superior I hope I can get a replacement panel for it.

Alive and going strong. Superior Fireplaces (http://www.superiorfireplaces.com/)

So, stupid question here... how can I tell the manufacturer of the fireplace? I am having the same issue with a hole in the fake brick. Thanks.

So you do not have the instruction book that came with the unit? Does this fireplace have heat recirculating grills top and bottom?

No, the house is 25 years old and I have only been there a bit over a year. Not sure where the circulating grills are.

The grills, if it's a heat recirculator, will be louvers the width of the fire box opening. The top grill or louver allows heat out into the room and the lower grill brings in cold air off the floor area.

The grills, if its a heat recirculator, will be louvers the width of the fire box opening. The top grill or louver allows heat out into the room and the lower grill brings in cold air off the floor area.

I have the same problem, mine does have a reciculator, but the back so so cracked it doesn't blow air out the top. I can't find my make or model number anywhere...

If you have a recirculator you can remove the lower louver and look for a label inside th cavity, use a flashlight.

I am sorry, this is a stupid question but how do I remove it? I don't see any screws on the top or front.

They can be different but on mine you just lift evenly on the lower louver. There are some pins top and bottom that hold it in position, when you lift the bottom pins come out of there holes. Once raised just pull out at the bootm edge.

I, too, am having this problem. We bought the house knowing that the fireplace was unusable. The back bricks are cracked and crumbling. I have a Superior insert, but have had no luck finding an insert from the manufactor. I did find a fireplace brick liner by Vanguard. Do you think that would work? Also, I've found cast iron panels that you place at the back of your fireplace to protect the brick work. Would this work, or is the damage too much for one of the cast iron panels?

Sorry Winkler, I missed the fact that this was still active. Can you give me a link to the Vanguard liner and/or the cast iron panels. They may work but I would need to see more info.

Here is the link to where I found the vanguard inserts
Vanguard 32'' Fireplace Brick Liner Kit - HFL3 : Homeclick (http://www.homeclick.com/web/catalog/product_detail.aspx?pid=195456)

And here is a link for cast iron panels
Fireplace Firebacks | Pennsylvania Firebacks | Cast Iron Fireback (http://www.woodlanddirect.com/Fireplace-Accessories/Firebacks?source=google&gclid=CIrJm6-X9pECFQUqlgodj2Lvxg)

Both would probably work for you. Vanguard does not tell me much about the material they use but it must be heat proof. Depending on the thickness of the Vanguard material you might leave the old crumbly stuff in place too.

I, too, am haveing this problem. We bought the house knowing that the fireplace was unusable. The back bricks are cracked and crumbling. I have a Superior insert, but have had no luck finding an insert from the manufactor. I did find a fireplace brick liner by Vanguard. Do you think that would work? Also, I've found cast iron panels that you place at the back of your fireplace to protect the brick work. Would this work, or is the damage to much for one of the cast iron panels?

Another option for you, would be to remove the old refactory and reline it with the thin firebrick, using a wire mesh as backing.

I rebuild these . The best way to repair these fireplaces is to remove all the panels and replace them with real firebrick "splits" 1 and 1/4 inch thick . I rebuild these .
I'm seeing more and more of them needing to be rebuilt . I have pictures and details on how to repair them if anyone wants to see them . 43 years in the Masonry trades . Semi retired .
Alan

I have a 20 year old mobile but I don't know what brand it is
The firplace has shifted a little and there is some opening
Between the panels hpw can I patch it up

My house from what I have been told was built in the 70s and from me spraying water on the fire to dye down the fire I have cracked the bottom of the fireplace and am wanting to sell and don't know how to repair it... HELP!!

I have a fireplace which is 20 years old. It doesn't heat radiators just a fire. It has developed cracks in the back and side walls. Please advise...