Hello,

I have a question regarding my bathroom plumbing. I have a 1.5" pipe coming out of the wall which goes into a p-trap. I bougth a new vanity and would like to raise that ptrap up a bit to be inside of it. Would it be possible to put an Elbow up from the 1.5" pipe, then another elbow going back out and into a p-trap. When I think of it visually it makes sense, but would the water drain okay?

So in summary. Pipe out of wall, elbow pointing up elbow->elbow pointing back out -> P-trap -> popup drain.

Thanks for any assistance here.

Jay

You can not raise the pipe coming out of the wall the way you describe, water will not run up hill. The only way to accomlish what you want is to open the wall to get access to the drain pipe inside. If that pipe runs horizontal you are dead in the water.

You can not raise the pipe coming out of the wall the way you describe, water will not run up hill. The only way to accomlish what you want is to open the wall to get access to the drain pipe inside. if that pipe runs horizontal you are dead in the water.

Thanks for the fast response. So the p-trap has to drop below the main pipe? Sounds like I may have to bring the p-trap up through the bottom of the vanity. Where would the water have to run uphill if the water is coming down through the drain, into the ptrap and through to elbows. For some reason it all seems downhill to me, but I'm sure I'm missing the whole thing here.

Is it possible for you to cut some of the rear of the vanity's frame rather than try to change the drain. Out through the floor of the vanity would be an S trap rather than a P trap, illegal in USA unless you were replacing a grand fathered S trap previously installed.

I have attached a picture setup here if it helps. Im starting to thing I should just get an open Vanity instead of a closed one. If the visual gives you any Ideas please shoot them my way! Thanks again for all of this help.

Jay

How about a picture of the back side of the vanity. Considering where the shut off valves are you may need to remove nearly all of the back side.

Here's the back and front of vanity.

Hate to be a pain but the pic of the back is too close. Step back so I can see the entire frame please.

Yea that's a pretty bad shot. I'm actually at the office now. Here is the site I bought it from with description

SuperiorBath.com: Brussels - Solid Wood Bathroom Vanity, Vanities By Size: 31" to 49" (http://www.superiorbath.com/proddetail.asp?prod=Brussels)

Basically there are the two bars across the back for mounting to the wall. They initially told me it was open in the back. To me that is not open.

I was going to put some chrome legs on it to avoid mounting it (that wall isn't the strongest either.. prewar building.)

Thank so much for looking into this with me, I was sort of at a dead end myself.

Jay

Is this what you want to do ? See the pic...

That cabinet looks OK to me. Why do you want to raise the trap ? Is the backing right over the drain ? If positive, than simply north the backing board.

Milo,

What is an "S" trap?

It would seem the problem of the trap has already been addressed by the manufacture when they supplied a hole in the shelf for the trap raiser to connect to the lavatory tailpiece.(see image). You may have to drill holes in the back for the stubout and water lines but the shelf looks fine. Am I missing something here? Regards, Tom

What Milo showed in his picture is what I was thinking, to get the p-trap inside of the cabinet. I'm so close to sending this puppy back. I hope we can figure this thing out once and for all. I think I can drill a whole in the bottom center of the middle of the cabinet in the back t bring the pipe in, then put that elbow going up from there.

Any other thoughts before I throw the whole vanity out he window? :)

Thanks guys.

Jay

What did you ever end up doing? We just ordered same vanity and are worried about same thing - our pipe from wall is below cabinet. D'oh!