We have had an ongoing problem with a slow kitchen drain. My husband has been using a "drain king" (drain ?) for almost a year. A week ago the aging "king" separated from the nozzle on the hose and is stuck approx. 4 to 5 feet in the elbow of the pipe. Have called out 2 "roto rooter" type plumbers to get it out and it will not budge. One plumber has a $5000. Solution, anyone here have any ideas? Not sure what to do or who to turn to... all help appreciated


Forgot to mention that when they snaked it they put about 4 different bits on the end and none worked. Is the corkscrew looking one call and auger. Regardless it did not retrive the part that got stuck in the pipe. Is there anything else they might use?

Your house must be built on a slab.

Yes it is on a concrete slab. Home is approx. 40 years old! Thank you

Since the "drain King is probably stuck in the first turn and I don't have Marks fancy tools, for $5000 (or to save $5000) I would either;

A: Dig down on the outside and tunnel under the footer to get to the pipe. It's probably close to the exterior wall right?

B. Remove the sink cabinet or cut out the bottom, rent a chipping hammer and go thru the floor to the first turn.

Any possibility of finding where drain goes into stack and going in from that way with snake and pushing "drain King" back up pipe. Its probably wedged at the turn and would come back easier than pushing through.


Mark
I don't think you should have deleted your post. Too much heplfull information there. Please repost.

Going to run these solutions by my other half and let you know how it goes... will check in tomorrow and see if anything new! Thank you soooooo much!!

We have had an ongoing problem with a slow kitchen drain. My husband has been using a "drain king" (drain ?) for almost a year. A week ago the aging "king" separated from the nozzle on the hose and is stuck approx. 4 to 5 feet in the elbow of the pipe. Have called out 2 "roto rooter" type plumbers to get it out and it will not budge. One plumber has a $5000. solution, anyone here have any ideas? Not sure what to do or who to turn to.... all help appreciated


forgot to mention that when they snaked it they put about 4 different bits on the end and none worked. Is the corkscrew looking one call and auger. Regardless it did not retrive the part that got stuck in the pipe. Is there anything else they might use?
You say they used a number of auger tips and still couldn't pull it back?
This is what's stuck,(see image) right? Did they use a retrieval bit, (see image) or a small auger to attempt to pull it back? This object is made of neoprene that can be augured into if you put enough muscle into it.
Forget the $500 repair. A good man with the right auger tip should be able to drill into the neoprene and pull it back.
I have a question. Why was the Drain King so far down the drain line?
You only had to run it up the trap tail for it to work. 5 feet is almost to the sanitary tee in the stack. Just curious. Tom

Tom, that's a $5000 solution.

My next suggestion was going to be what I think you would have said, "snake it from the vent". You loose some of the ability to put pressure behind the snake as it makes a lot of turns.

Harold,
I was under the impression that the Drain King was caught in the horzontal drai in the wall. Where does it say they went down a vent?
MSBoznos, What did you put the Drain King down? The wall stubout or the roof vent? Cheers, Tom

Hubby put the drain king into the clean out trap, outside
The house, directly adjacent to the kitchen sink. I may
Have over estimated the length it went in. Plumber said
He is guessing it is caught in the bend of the pipe. The
Picture showing the auger tip looks very much like the
One they used. They used others as well, all they had
With them... man using the snake was a very large man
And appeared to be apply a lot of muscle behind it.

Going through the vent on the roof might fix it?
Thank you for your answers...


Since the "drain King is probably stuck in the first turn and I don't have Marks fancy tools, for $5000 (or to save $5000) I would either;

A: Dig down on the outside and tunnel under the footer to get to the pipe. It's probably close to the exterior wall right?

B. Remove the sink cabinet or cut out the bottom, rent a chipping hammer and go thru the floor to the first turn.

Any possibility of finding where drain goes into stack and going in from that way with snake and pushing "drain King" back up pipe. Its probably wedged at the turn and would come back easier than pushing thru.


Mark
I don't think you should have deleted your post. To much heplfull information there. Please repost.

This sounds a lot like what he suggested, price tag was between $3ooo.-$5000.

Having my Grandson come over today to take a look and will show him all your
Suggestions. Thank You so much, will keep you posted!

The plumber came out again this morning, he bought a new auger much bigger than the one he used yesterday, he got the "drain king" out in about 45 seconds. Whoooopeeeee!!
This man's determination made my day! Many thanks to all of you for your idea's... MsB

You're entirely welcome! We're just glad you got The object removed. Now go purchase a hand held snake and forget the Drain Kings and Clog Blasters.
What they don't mention is that they're useless if there's a vent upstream from the blockage. Good luck and if we can ever be of servcice in the future, just ask. Tom