PDA

View Full Version : Armstrong won't turn on


darkevo
Jun 14, 2009, 12:55 PM
I have 2 armstrong heat pumps. One for the upstairs and one for downstairs. They are both about 3-4 years old. The thermostat for the upstairs unit stopped working so I replaced it with a rightemp. The unit upstairs no longer will turn on... I switched the thermostat out with the one downstairs and it works just fine, so I know that the thermostat works. I have checked the power from the circuit breaker to the outside compressor and the inside unit as well and the both have power. I am at a loss. I have tried new wires from the thermostat to the unit and still nothing. Any advice would help a lot.

Thank you
Matt G.

Joshdta
Jun 14, 2009, 12:58 PM
Did you hook up a blue wire? Or put a jumper from rh to rc?

darkevo
Jun 14, 2009, 01:04 PM
Yes there is a blue wire that I hooked up, in addition to the battery power. The new thermostat came with the jumper already attached. And I followed the instructions to the "t"

Joshdta
Jun 14, 2009, 01:06 PM
OK with the new stat on does the fan on or the heat work? Or is it just the ac that is not working?

darkevo
Jun 14, 2009, 01:18 PM
Nothing works. No fan, no heat, no ac. Like I said I switched it out with the one downstairs, the old ones, made by armstrong are identical, and still doesn't work. I have placed the new rightemp one downstairs and it works fine.

Joshdta
Jun 14, 2009, 01:20 PM
Did you turn off the power while you were changing stats, may be you blew the little 3 amp fuse on the furnace control board.

darkevo
Jun 14, 2009, 01:22 PM
The power was off but where is this control board, ill check the fuse anyway.

Joshdta
Jun 14, 2009, 01:24 PM
Should be in the bottom door of the furnace, fuse should be a small 3 amp car type.

darkevo
Jun 14, 2009, 01:30 PM
I see no fuse in there... I followed all in going and out going wires and looked at all the components in side of the unit.

Joshdta
Jun 14, 2009, 01:38 PM
OK some unit do not have a fuse. Do you have a volt meter?

Check for 28 volts between r and c

Or put a jumper from r to g at the stat and see if the blower comes on.

darkevo
Jun 14, 2009, 01:47 PM
No I have no voltmeter so I put the jumper between R and G. nothing happened...

Joshdta
Jun 14, 2009, 01:54 PM
sounds like you have a bad transformer. If you are gettting no power.

Other things to check=

Breaker to indoor unit, fuse at switch for indoor unit. Bottom door on good so the door safety switch lets power threw. If these are all good then the transformer is next in line. Inless the is a safety switch on the drain some where.

darkevo
Jun 14, 2009, 01:57 PM
How can I check the transformer?

Joshdta
Jun 14, 2009, 02:01 PM
Well you said you saw no fuse on the control board. Is there a light on it? If it lights up then you probably have 24 volts if not then probably don't. No other real way to test with out a volt meter.

darkevo
Jun 14, 2009, 02:09 PM
An LED? I see no light...

darkevo
Jun 14, 2009, 02:09 PM
Also I see no cca, is that what the switch would be on?

Joshdta
Jun 14, 2009, 02:29 PM
Cca?

darkevo
Jun 14, 2009, 05:04 PM
Circuit Card Assembly. I assume that's what the fuse and transformer would be on...

Joshdta
Jun 15, 2009, 04:32 AM
Yes a led on the circuit board, its like the fuse some units have them some not.

darkevo
Jun 16, 2009, 09:59 AM
So I acquired a voltmeter... I checked the transformer, it has the ~220 going in but not the 24v going in. how/where can I get a new transformer?