PDA

View Full Version : Installing a bathroom flange


windham
May 29, 2008, 09:20 AM
I am replacing an old toilet and found that the toilet was screwed onto the wooden floor (four screws). There was no flange. Is there a flange that can be screwed into the wooden floor?

ac101
May 29, 2008, 12:15 PM
Absolutley, what type of pipe do you have ? There are a few choices this one is just astandard glue up but there are others for other applications. If I missed anything post on back. GOOD LUCK, AC

massplumber2008
May 29, 2008, 12:26 PM
Hey Windham:

AC101 has you headed in the right direction... as he asked... what kind of pipe?

If this is as old as you suggest I am wondering if you see a grey pipe in the floor... with the edges peened over about 1" or less... hmmm..

If that is the case, then you have a lead pipe there. Be very careful with this pipe as it can tear quite easily and then will need to be replaced!

If you have lead you can use a brass flange or a repair flange to make this work for you... see pictures.

If you use either the brass or the repair flange, you should just need to set in correct placement/alignment (for johnni bolts to line up) over the old lead pipe and screw the flange down to the floor (covers the peened lead rim of the old lead pipe). Then would use a horned wax gasket (see pic.) to set the toilet bowl and you should be all set.

If not a lead pipe and lets say it is a black cast iron pipe... then using a TWIST AND SET flange (see last pic.) will work fine! But... does not sound like a cast iron pipe.

Let us know what you think... MARK

.

windham
May 29, 2008, 01:38 PM
Hey Windham:

AC101 has you headed in the right direction...as he asked...what kind of pipe??

If this is as old as you suggest I am wondering if you see a grey pipe in the floor...with the edges peened over about 1" or less...hmmm...?

If that is the case, then you have a lead pipe there. Be very careful with this pipe as it can tear quite easily and then will need to be replaced!!

If you have lead you can use a brass flange or a repair flange to make this work for you...see pictures.

If you use either the brass or the repair flange, you should just need to set in correct placement/alignment (for johnni bolts to line up) over the old lead pipe and screw the flange down to the floor (covers the peened lead rim of the old lead pipe). Then would use a horned wax gasket (see pic.) to set the toilet bowl and you should be all set.

If not a lead pipe and lets say it is a black cast iron pipe...then using a TWIST AND SET flange (see last pic.) will work fine!! But...does not sound like a cast iron pipe.

Let us know what you think...MARK

.

Thanks for the reply. The pipe is plastic and the last image that you show looks like the one that I can use. Do I have to glue it to the pipe or can I just insert into the pipe?

windham
May 29, 2008, 01:41 PM
absolutley, what type of pipe do you have ? there are a few choices this one is just astandard glue up but there are others for other applications. If I missed anything post on back. GOOD LUCK, AC

Thanks for the reply. It is very helpful. The pipe is plastic and the image that you sent looks like the one I can use. Do I have to glue it or can I just insert it into the pipe?

ac101
May 29, 2008, 02:01 PM
I would definitley glue it on just be sure to test fit it first. Better to find any problems before glue is applied. If you have black pipe (ABS) then be sure you use the ALL PURPOSE GLUE. If the pipe is white(PVC) then PVC glue should be fine. The type I showed you can be picked up at any Lowe's or home depot. GOOD LUCK, AC