??
Hi
I have a hampton bay sidewinder ceiling fan that came with a wall mount remote control. I wanted to have a hand held remote control, so went and purchased a remote control that came with its own receiver (hunter). I replaced the original receiver with the new receiver. The hand held remote control that I purchased did not have the button that would allow me to reverse the blade on the ceiling fan. That was OK with me because I only needed the fan to operate in the regular mode (counterclockwise-cool air going down). But now that I turn the fan on , the blade are in the reverse mode (clockwise-warm air down). Is there anyway for me to make the blades go the other way (counterclockwise). My fan does not have any exterior switch that would allow me to change the direction of the blades

Please help! Thank You

I have 4 Hampton Bay hand held remotes, It may not be the easiest solution, but the automatic temperature- fan speed control IS worth the extra effort and money in my book.

That is a fun one.

The fan will change direction by itself if it is running and the power snaps on and off a couple of times. Another, thanks to the power company.

Here is how I fix it.

Turn the fan off and spin it in the direction you want it to go.
Then quickly snap the power on and of once or twice within a second or two.
If you have a wall switch it makes it easier, but you might need to do this from the circuit breaker, with 2 people, one to spin the fan.

Basically on the first snap, the fan will start to slow down because you spun it in a direction it does not want to go and it is trying to go the other way. On the second snap of the power, it should click, and pick up speed in the right direction.

You may have to try 3 or 4 times with 2 to 3 power snaps, but it almost always takes. This works for almost any reversible Hampton Bay fan, BTW.

I just tried the turning the fan in the direction I wish it to go and then turn off the electricity at the switch on and off and IT WORKS! I am just amazed! Thanks for the advice!

I was in a funk! I had a ceiling fan(Hampton Bay) installed,with a wall switch and dimmer. The installer tossed the remote,and I found out later I had to have it to reverse the direction! I have 20ft.ceilings,so I had no way of bringing the warm air back down. I started looking for places to buy a remote when I happened onto this site and found akabob's sage advice regarding the "spin it and hit the switch" plan. I tried it 3 times and it finally worked! You saved me $40.00! THANKS!! :D

Ok, two things surprise me about this thread. I have been repairing ceiling fans for several years, but you can always learn something new.

1. I have never heard of AKABob's solution before. Rest assured I will be trying it as soon as I have a chance. The one thing that surprises me is that you spin the blades by hand. Moving the blades by hand should have absolutely no bearing on how the remote receiver performs. Have you tried the same solution with just flipping the switch, without turning the fan blades? That part of the solution doesn't surprise me as much. Before the popularity of wireless remote controls, electronic ceiling fans that were controlled but numerous flicks of a wall switch were common, in the 80s. Casablanca's "FLIK MODE" comes to mind. Do keep in mind that remote fans are not meant to be controlled by wall switches and you do run the risk of causing a small power surge.

2. I am surprised the original poster's replacement remote and receiver worked.

I'll tell you why. There are two types of remote control ceiling fans. Those where the receiver is built into the fan assembly (either in the motor housing or switch housing) and those where the receiver is replaceable and/or sold separately (usually mounted in the canopy). In the vast majority of cases, fans of type #1 are reversible via the remove, and #2 are reversible by a switch on the fan. If your fan was originally reversible by the remote, I am surprised you were able to get it to work with a replacement receiver without the additional wires for reverse.

I think the easiest solution to the original problem would have been to purchase a handheld remote that worked with the original receiver AND the wall control. A universal remote would have done it.

For more information about ceiling fan remote problems, try:

http://www.ceiling-fans-n-more.com/ceiling-fan-remote-controls.php

Right on the money as to my problem a way to get around the remote not reversing

My fan was stuck on reverse when my remote broke. I purchased a replacement remote at Lowe's or Home depot, can't remember! BUT it didn't have a reverse button on it. I found somewhere on here reversing the pink and yellow wires on my Hampton Bay fan worked to get it to go the right direction. It was bugging me for 6 months until I finally googled all day trying to find a solution. Now I'm a happy camper my fan is blowing down instead of sucking up... :)

My remote for my hampton bay ceiling fan just quit working tonight. I changed the battery and the light comes on the remote but does not start the fan or turn on or off the lights what's wrong?

Did the light on the remote come on before you changed the battery?

Make sure the frequencies match. If that doesn't work, you probably need a new receiver.

Ceiling fan remote controls - help and FAQ- Ceiling Fans N More (http://www.ceiling-fans-n-more.com/ceiling-fan-remote-controls.php)

Thank you, thank you, thank you for sharing this unbelievably effective solution to my reverse problem, AKABob. We installed a new Hampton Bay ceiling fan yesterday with remote operation only. The fan speed and tight work with the remote, but the fan was set to winter rotation and the reverse button on the remote doesn't do anything. With the fan off, my husband began rotating the blades in a counter clockwise direction. I hit medium speed on the remote, turned off power via the wall switch (that was in place for the light fixture we had before the ceiling fan), turned power back on via the wall switch, and hit medium on the remote--all in rapid succession. Voilà, the fan blades continued in the desired direction.

This solution saved us a lot of aggravation and work and money. My only question is, how come Hampton Bay has not addressed this long standing problem? Persistence on the Internet and the generosity of humans willing to make the time to share information is the winner here.

Because Hampton Bay wants you to buy a new fan as soon as you have the slightest problem.

Just reporting that I called Hampton Bay about the remote not working to reverse the fan. I was told that I needed to have the fan running on low and then press reverse on the remote control. If that doesn't work, customer service told me to press reverse while running the fan on medium. (Some fans are set to reverse on low and others on medium.) Nowhere in the manual is this addressed. I had been pressing reverse with the fan turned off, which seemed to me a logical thing to do. Live and learn.

I assumed you could reverse the fan on any speed. Most fans you can.

Someone else wrote in that their 2 year old hit reverse on the remote when the fan was operating on high, followed by strange noises and complete malfunction. But who knows...

THAT definitely shouldn't happen.

AKABoB - YOU ROCK. I've put up with my fan operating in the wrong direction for months. I tried all the obvious thinks to get it to reverse; pressing the reverse button on the wall remote switch when the fan was off, holding the reverse and low fan setting, holding reverse and pressing all three speeds, NOTHING WORKED!!

Thanks to you, I did the suggestion technique; spin the fan in the reverse (down) direction and switched the fan wall power switch off and on and then pressed low and WALLA- it keep spinning in the new direction (I had to do it twice)!!

SO AWESOME! Thanks for your help. I'll be able to sleep much cooler now. A few degrees makes a big difference in the Phoenix, AZ heat!

Thanks again! :D

I could not get my Horchow fan manufactured by Ellington to reverse. I tried the manual method several times as prescibed by AKABoB and it actually worked. My fan is about 11' up. I used my telescopic lightbulb removal tool to push the fan in the clockwise direction (direction I needed) and flipped the wall switch on 1 time. First time it did not work and the fan would revert to spinning in the counter clockwise direction. I then pushed the fan faster and flipped the wall switch on again; still did not work. I tried this a few more times whereas I would flip the wall switch on every second as the fan turned clockwise, again it did not work. Irritated, I spun the fan clockwise, not to fast, and flipped the wall switch on and off just as quick as I could (not sure how many times I flipped the wall switch) and it started turning in the clockwise direction.

As a warning, I do not think it is a good idea to flip the fan wall switch in a hurried fashion. I read in the string where the CeilingFanRepair person warned against building a surge that could cause damage. I recommend heeding his advice. My rapid succession of switch flipping may have been circumstantial.

Thank you AKABoB!

I would also like to thank CeilingFanRepair for his insightful and seemingly accurate answers on ceiling fans. I really appricate your efforts.

TXHomeowner

Thank you.

BTW Litex makes Ellington Fans and they have a website and customer support.

ALTURA REVERSE PROCEDURE WITHOUT REMOTE

AkaBob, you rock!

I just wanted to add a few Google key words for other Hampton Bay customers who have purchased this fan and have lost the remote. The fan has no switches, and most would assume you would need a remote to control the unit fully.

I had mine installed on 20 ft ceilings, and the installer forgot to install the remote receiver with the fan! I thought I was never going to be able to fix this without another service call, however, I just flicked my wall switch between HI and OFF 2-3 time in a row, and did not even have to spin the blades in the direction I wanted to go! Presto! The fan began operating in the other direction! Now, I can change directions by hitting the switch a couple of times in the future, and do not need the remote!

How do you change the speed with no remote?

Amazing what you can find out on the internet! I don't remember what brand my fan is but it has a hunter remote. When I installed it a year ago it was going the right direction but I turned it on the other day and its going the wrong way. I tried akabobs solution. I used a pole to turn the blades in the other direction and it started turning in reverse after about the third time. I'm an electrician and I think in electrician school I remember something about certain types of electric motors that will turn in what ever direction they are started in. I don't know for sure about that but I'm ecstatic my fans going the right direction and I didn't have to drag a ladder out and tear my fan apart to fix it. Thanks

I think it's more about tricking the receiver circuitry. Whenever I try to convince my non-remote fans to spin the other way, they aren't so easily fooled.

I have several remote ceiling fans (hunter brand). I recently added two ceiling fans (also hunter) in the living room. I am continually having RF interference problems; lights & fans go on and off sporatically. I have changed the code on the receivers and the transmitters several times with no luck. I have even had an electrician come check the switch and wiring - all okay. Any suggestions welcomed.

Changing the codes is the only option. If you can't find enough different codes to operate each fan, check with Hunter Fan Ceiling Fans, Air Purifiers, Humidifiers, Thermostats (http://www.hunterfan.com)

Ceiling fan remote controls - help and FAQ- Ceiling Fans N More (http://www.ceiling-fans-n-more.com/ceiling-fan-remote-controls.php)

My husband and I just did it!! It really works! After over a year we were about to buy a new fan and gave it a final try to look for solutions and AKABob's solution worked on the 4th or 5th time. It's working just fine on the right direction. KUDOS AKABob!!

AKABob's technique works! We just fixed our fan and it is going in the right direction now!! Wow! We were about to buy a new one tonight when we gave it a last try to look for a solution. It worked on our 4th or 5th try!

Adding my Happy man post... I have a Hampton Bay Sidewinder fan that I am not using the receiver or wall remote switch. I think the wall remote is ugly and wanted to use a fan switch/light dimmer switch to match the rest of my switches style and color. Plus I'm worried that with my little kids that the buttons will be too enticing for them to leave alone. My fan turned clockwise out of the box and I needed to switch the direction. AKABob's suggestion work! My wife's first attempt failed but on the second she gave the fan a good spin by hand in the desired direction, then turned the switch from off to high and back to off once a second, three times. On the third it was running the correct direction. Thank you everyone.

Many fans come with blades that are pretty on the top side, too. You can take the blades off and turn them over. Then the bend of the blade may go the other way, if it is that style.

OK I have a Hampton Bay Altura a 68" fan for an over-sized room, my issue it seems to me the fans turns very slowly even on high. I feel it should turn at least twice as fast. I use the remote control to turn it on, off, low, med & high and the light which we usually never use. Any feed back would be appreciated

Received a remote with no instructions chq8bt7053t... what do I do with it? Can someone help

Looking for a Hunter fan with a wall or remote that has reverse... installing on 20 foot ceiling and can't throw the switch on the fan.

It has to be a white fan and it has to have blade of 52in

Any suggestions on which Hunter fan??

Own a Hunter ceiling fan remote part no 86603-01, not instructions on setting a reverse, your suggestion worked after the 3rd try, thank you for saving us $$$.

I have a fan by Fanimation and have tried the above suggestions for reversing the blades with no luck. Are there any other ideas? No switch on the fan mounting, and no reverse button on the remote. I need to have it go counter clockwise for winter. Thanks for any help or ideas someone might have,

Turn the fan off and spin it in the direction you want it to go. Then quickly snap the power on and of once or twice within a second or two.
If you have a wall switch it makes it easier, but you might need to do this from the circuit breaker, with 2 people, one to spin the fan.

Basically on the first snap, the fan will start to slow down because you spun it in a direction it does not want to go and it is trying to go the other way. On the second snap of the power, it should click, and pick up speed in the right direction.

You may have to try 3 or 4 times with 2 to 3 power snaps, but it almost always takes.

We have a non-Home Depot fan in the dining room that was in "winter" mode, with no switch to change it. I read this idea and thought... you got to be kidding me! But what the heck, I tried it. About the 4th or 5th time, dang it, it reversed to counter-clockwise/summer mode. Living proof that even at age 63 you can learn something new.

John in Wisconsin