View Full Version : 'C' connection on new thermostat
volan
Jun 20, 2007, 04:21 PM
I am considering purchasing a Honeywell W8665A remote control thermostat. I have the wiring diagram and I am a bit confused. I'm hoping someone can help me.
My current thermostat attached to the wall has the following wires available:
Y, G, R, W.
The manual for the W8665A states that C must be connected, but I have no 'C'. Apparently the C is a common coming off the transformer.
Am I out of luck or is there a way around it?
hvacservicetech_07
Jun 20, 2007, 05:57 PM
I'm pretty sure you'll need a common to power that thermostat, if all you have is four wires sticking out of the wall, simply pull a 5 ct cable and hook the common up on the furnace, this may be pretty easy if they didn't attach the wire to a stud inside the wall, just connect the new wire and old and pull it down through the wall.
volan
Jun 20, 2007, 09:20 PM
Thank you. I'm not confident pulling a cable from the basement up to the 2nd floor of my house. Perhaps I'll consider professional help.
But at lease now I know that I need the 'C' wire and I won't rush into buying the unit until I know what I'm going to do.
Thanks again.
hvacservicetech_07
Jun 20, 2007, 09:22 PM
Is there a reason that you want that thermostat? There are some nice stats on the market that would work just fine, and they have a nice look.
hvacservicetech_07
Jun 20, 2007, 09:28 PM
Keep in mind, it wouldn't cost you very much to call in a pro to pull a new wire and install the thermostat, your talking an hour labor or less.
volan
Jun 21, 2007, 07:09 AM
Is there a reason that you want that thermostat? There are some nice stats on the market that would work just fine, and they have a nice look.
The current thermostat is located in a hallway in front of a big picture window so the temperature reading is not what the temperature in the rooms are. That's why I wanted a remote control thermostat. That way I can put the sensor in one of the rooms and the temperature control will be more accurate.
volan
Jun 21, 2007, 07:11 AM
Keep in mind, it wouldn't cost you very much to call in a pro to pull a new wire and install the thermostat, your talking an hour labor or less.
Only an hour? I'll check into it. Thanks.
biggsie
Jun 21, 2007, 08:58 AM
The transformer supplies 24 vac (C is common for 3 relays -- cooling --heating -- fan and common for thermostat power Fig.2 The other leg is R which provides
Power to thermostat, and is jumpered to RZ terminal...
http://customer.honeywell.com/techlit/PDF/69-0000s/69-1630.pdf
Inside wall would be good location for thermostat Maybe a new run would work...
volan
Jun 21, 2007, 09:08 AM
Yes, I plan to put the thermostat in one of the rooms away from direct sunlight
tazdec
Jun 21, 2007, 03:14 PM
I am considering purchasing a Honeywell W8665A remote control thermostat. I have the wiring diagram and I am a bit confused. I'm hoping someone can help me.
My current thermostat attached to the wall has the following wires available:
Y, G, R, W.
The manual for the W8665A states that C must be connected, but I have no 'C'. Apparantly the C is a common coming off the transformer.
Am I out of luck or is there a way around it?
See if your stat reads power stealing if not you need a common to the stat see if you have a extra wire in your stat wire if you do you can hook up c at the unit and the c at the stat
volan
Jun 21, 2007, 03:29 PM
see if your stat reads power stealing if not you need a common to the stat see if you have a extra wire in your stat wire if you do you can hook up c at the unit and the c at the stat
Thanks for your post.
I don't actually have the thermostat yet. I'm just doing my due diligence prior to purchasing it. I find that doing work upfront results in less frustration afterwards.
The only wires I have at the T-stat are those that I have mentioned. There do not appear to be any spare wires that I can see.