When we bought the house 4 yrs ago, the previous owners gave us 4 different codes (she couldn't remember the code) for our Craftsman wall mounted keyless entry garage door opener which is mounted outside the garage door. None of the codes she gave us ever worked, so we never bothered with it. Now we would now like to use it and was wondering is there a way to reset the code?

Garage Door Opener Unit # - 139.53970SRT Model; Craftsman

Car Remote # - 139.53681B Model; Craftsman

Keyless Entry # - I cannot find the number, unless its on the backside of the unit which is mounted to the side of the garage. Craftsman

Any help would be appreciated! :confused:

Change batteries first, Do you have learn button and led on Operator. Don't know if model
Works likes this. Hold learn button for maybe 8 seconds, to clear codes.
Next, wait 30 seconds, press learn for led to light, go to keypad, and enter C O D E,
Enter. C O D E is your new combo(numbers)
I will look for exact info. If its not working, you can't hurt it.

Thank you for responding. We did change the battery, that didn't help. Can I e-mail you a picture of the unit (sorry I don't know how to attach a picture on this site). I don't see a learm button or an LED, but maybe you can point that out on the pic. Thanks again for the help.
KellyGirl

Do you see small wire hanging out, may be antenna, should be close. Usually on back side of Operator. You may need ladder, Be careful..

You must be talking about the garage door opener itself? Yes, there is a wire there!

I know this is going to sound stupid, but the Operator IS the garage door opener its self your referring too, right? (You're working with a blonde here, so bare with me) ;-)

Your Doing Fine, I work well with Blondes
Found these:

SEARS CRAFTSMAN GARAGE DOOR OPENER, AUTOMATIC DOOR OPERATOR COMPATIBILTY CHART (http://www.liftmaster-garage-door-openers.com/searsboards.htm)

Chamberlain Garage Openers: craftsman garage door openers, LIFT MASTER GARAGE DOOR, lift master garage doors (http://www.liftmaster-garage-door-openers.com/codingindex.htm)

How to change Craftsman Garage Opener Frequency [Archive] - DoItYourself.com Community Forums (http://forum.doityourself.com/archive/index.php/t-220065.html)

Okay, I looked up the sites - I think my husband and I might be able to figure this out. I will post again, to let you know if we were successful in getting this resolved. I want to thank you again for all your help, it is truly appreciated! I've never used this site, I just kind of stumbled upon it, but its really nice to know that there are people out there that still like to help others!

Again, thank you!

KellyGirl

A pleasure, any more questions? Come back
Take Care

Are the batteries OK? If so, proceed.

You will need 2 people, one outside with the door closed and one inside who is able to reach the control panel on the unit.

The person on the outside should enter the 4 digit password desired and HOLD the enter button.

The person on the inside presses and releases the SRT (learn) button while person on outside continues to hold the ENTER button. My SRT button is orange.

After the light flashes on the panel the person on the outside releases the ENTER button.

Test by pressing the 4 digit password and enter. Hopefully, the door will open.

When doing this procedure, does it reset the remote openers as well?

Directions for your model will tell, sometimes when you press the Learn button longer than required for adding a remote, it CAN? Erase all codes.

..

How do you change the code to your keyless entry to my garage door. Linear LCC Model LD033

Need help on how too change my keyless entry thry my gargage door. Linear LCC Model LD033

Amarr Garage Doors - Over 60 years of garage door manufacturing excellence (http://www.amarr.com/residential/service_and_support/owners_manual/)

Your model is at the bottom of the list, includes operating instructions, Take Care

To Add a Remote Control
1 Press the opener's LEARN button. The red LEARN
Light will glow. The red light will stay on for about 15
Seconds. A remote must be added while the red
LEARN light is still on.
2 Send a signal from a remote. The red LEARN light and
The opener's light will fl ash once indicating that the
Opener has accepted the remote.
3 Repeat Steps 1 & 2 for any additional remote controls.
To Remove all Remote Controls
1 Press and hold the opener's LEARN button for ten
Seconds or more.
2 Release the LEARN button. The red LEARN light will
Blink three times signaling that all of the remotes
In the opener's memory were erased. The red
LEARN light will turn off, then turn on for 15 seconds.
A remote control can be entered during this time using
Step 2 above.