View Full Version : Toilet will not refill
gypsyjt
Aug 21, 2008, 08:49 AM
When you flush the toilet, the tank will not refill. Do we need to replace the part that is in there?
afaroo
Aug 21, 2008, 09:15 AM
See the images below and tell us which type is your ballcock inside your tank, and give us some more info after flush is the water coming into tank,does it run and don't stop or just tank would not refill, you may need to adjust the water level, please tell us about the ballcocks, Thanks.
John
gypsyjt
Aug 21, 2008, 09:27 AM
400A.
The tank will not fill. I pushed down on the thing and now it is up higher than the tank. If I push it toward the back bubbles form at the bottom and the tank will fill very slowly as I hold it there. No water comes out of the tube that goes into the refill thing.
speedball1
Aug 21, 2008, 10:38 AM
OK Gypsy,
Time to get down to specifics. Are you talking about a float ball (image #2)or a can, (image #1) when to talk about pushing down or lifting? We can't help if we don't have any details to work with. Soooo, give us some details to work with.Regards, Tom
afaroo
Aug 21, 2008, 10:44 AM
Close the angle valve under the tank, press down the fill valve top cap and turn it counter clockwise remove the fill valve cap cover, inspect the washer for wear or cracks. If bad replace it Replacing a bad washer is cheap and easy, if you decide to hunt for a washer, remove it and take it to the store to find a match.
If the washer looks good turn it over and install it
Before installing the washer you need to flush the fill valve, Cover the valve with your hand. Turn on the water (cautiously, so you don’t get a cold shower!) and let it flush out the valve for a few seconds.
Check the tank water level, it should be at the mark in the tank or 3/8 to 1/2" below the top of the over flow tube when the tank is filled and the ballcock shut down
speedball1
Aug 22, 2008, 05:17 AM
John's assuming that you have a FluidMaster Ballcock (see his image) But he mixed instructions for a regular ball cock and a FluidMaster. While you can reverse a washer in a regular ball cock you must replace a FluidMaster washer. We still don't know what ballcock that you have so it'd going to be difficult to advise you. How about answering our questions. Regards, Tom
afaroo
Aug 22, 2008, 08:00 AM
Thanks tom for correcting me yes I did, I think I put too many words in there, I bleive on his post #3 he indicated that his ballcock is 400A which is the fluid master, yes you are correct on this type ballcocks the washer to be inspected if any wear or crack should be replaced, Thanks.
Regards,
John
plumber_boi
Aug 23, 2008, 01:43 AM
Fluidmaster, Brasscraft, and Hydroclean are all the same basic design though.
speedball1
Aug 23, 2008, 04:40 AM
Fluidmaster, Brasscraft, and Hydroclean are all the same basic design though.
And that helps the asker how?
speedball1
Aug 23, 2008, 04:44 AM
Thanks tom for correcting me yes I did, I think I put too many words in there, I bleive on his post #3 he indicated that his ballcock is 400A which is the fluid master, yes you are correct on this type ballcocks the washer to be inspected if any wear or crack should be replaced, Thanks.
Regards,
John
I didn't get that his ballcock was a Fluidmaster from
The tank will not fill. I pushed down on the thing and now it is up higher than the tank. If I push it toward the back bubbles form at the bottom and the tank will fill very slowly as I hold it there. No water comes out of the tube that goes into the refill thing. I'm stiill waiting for him to let us know. Regards, Tom