Log in

View Full Version : Move toilet location


ghelnes11
Oct 1, 2007, 02:01 PM
How difficult is it to relocate a toilet less than 10 feet from where it is located now? We would like to install a whirlpool tub, but would need to relocate the toilet.

Flying Blue Eagle
Oct 1, 2007, 09:33 PM
Where is this at? Is it on concrete floor or conventional floor.? CAN you get under where it is at and going?? DId not have enough information::::

ghelnes11
Oct 2, 2007, 05:57 AM
The bathroom is our 2nd floor master bathroom. We are thinking about enlarging the bathroom to install a whirlpool tub. We would extend the bath into a closet. The bathroom has a 1 sink vanity, toilet and shower. The shower is next to the toilet. If we move the toilet into the closet and remove the shower we could install a whirlpool tub/shower in that location. The other option would be to enlarge the bath into the shower and part of the bedroom and put the whirlpool tub/shower there which would be the backside of the sink vanity. I would think that option would be easier, but the idea of a separate toilet and the whirlpool tub/shower when you first enter the bath seems more appealing. Your thoughts?

labman
Oct 2, 2007, 06:27 AM
It may not be so bad if in a major remodel you are going to rip up the floor and walls. Besides the drains, you must have everything properly vented. Getting all this right can be tricky. Your best thing might be to figure out what you have now, and what you want to do. Then post a sketch here and let our professional plumbers help you. We have some very good people here. I leave details on drains and venting to them.

ghelnes11
Oct 2, 2007, 10:36 AM
I am posting three drawing of the master bathroom. The first one is the bathroom now and the other two are ideas of how to add a whirlpool bath. I know this isn't much information, but there aren't any plumbing drawings and I don't want to tackle the job until I have a better feel for the difficulty or cost. Thanks.

labman
Oct 2, 2007, 12:31 PM
Quite often you will have a main stack running from below the house to a roof top vent. The waste goes down it pulling air in the vent as needed. Start moving drains and vents around, and you can run into code problems. If you are on a slab, it makes locating things tougher. Listen a little downstairs and you can identify where the drains go through the walls. The roof top vent is obvious. Also look for vent pipes in the attic. I can't tell you how to comply with codes and wouldn't trust some others. I just want to set it up so Tom can spike it.

ghelnes11
Oct 8, 2007, 10:49 AM
Does anyone ever answer these questions?

ballengerb1
Oct 8, 2007, 11:44 AM
OK here is a simple answer, its difficult. Most of the people who responded gave correct answers and very general advise but this task is over the heads of most home owners. To insure the new system works properly and meets code you likely need a real plumber to do the job or at least give you an estimate. We don't know your skill level so maybe you can tell us more about yourself..

labman
Oct 8, 2007, 12:09 PM
Before Tom or one of the others here can give a good answer, you have to post the info I suggested, where your existing drains and vents are. Which way the joists run would help too. It is much easier to extend a drain along a joist that across them.

With the proper advice here, likely you can do the job. Running PVC pipe is fairly easy once you figure out where to run it. There are easy ways to tie into copper without soldering too.

ghelnes11
Oct 8, 2007, 01:24 PM
I don't know where the existing drains or vents are. I also don't know which way the floor joists run. I though perhaps from looking where the toilet, shower and sink are presently one could tell what I would find once the floor and walls are opened up. I have done basic plumbing running PVC, replacing fixtures, etc. The main thing I don't have experience with is the venting. If you branch off from the existing toiler drain, do you need to run a new separate vent for the new toilet? Thanks,

ballengerb1
Oct 9, 2007, 07:50 AM
If you indicate which way your load bearing walls run we can determine the direction of the floor joists. Cutting a 5" hole through serveral joists, with the proper pitch, can be tricky let alone trying to get 10' of PVC through the new holes. Speedball1 can better answer your vent question.

ghelnes11
Oct 9, 2007, 08:41 AM
The load-bearing walls run the same direction as the 11' wall.

Flying Blue Eagle
Oct 15, 2007, 08:36 PM
ghelnes11 - LOOKing at the drawings you sent I would guess that the floor joist are running from your bedroom to left side of the print, which right behind the comode inside is the main 3" drain, the shower should be at least a 1 1/2" pipe that is " T" into main drain,and the sink drain the same way, if floor joist run the way I'M thinking ( JUST gussing) on what I can see,:::: The joist will be notched or holes drilled threw them for the 1 1/2 " drain line "t" into the 3" main line behind toilet You will probably find the vent line there also, and don't be surprised if it's only a pvc 1 1/2 " pipe . I HOPE I HAVE Helped I REALLY NEED EXACT MEASURMENTS ON NEW UNIT AND ON the stand up shower (OUTSIDE TO OUTSIDE) ALso inside wall to wall, measurements