Ask Experts Questions for FREE Help !
Ask
    ssimonsen's Avatar
    ssimonsen Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Nov 1, 2009, 06:43 PM
    Bryant Furnace RED LED light remaining on
    On Thursday evening I was going to attempt to change my filter, I took the 2 doors off the front of my Bryant Horizontal Furnace and was looking for filter. With no luck, I gave up and put the 2 front covers back on. Now the RED LED light is on, not flashing just continuously on.

    What should I do? I turned off my thermostat because I was worried what was wrong or happening. However, it is getting quite cold in here.
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #2

    Nov 1, 2009, 06:46 PM

    On the control board, or the back of the door, or your owners manual you will find the led fault codes. Solid red may be normal operation.
    ssimonsen's Avatar
    ssimonsen Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Nov 1, 2009, 06:51 PM

    The only information I can find is where it says that LED status codes: Continuous RED: Control has 24VAC power

    Is that OK?
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #4

    Nov 1, 2009, 06:54 PM

    Yep that means it is has power and should work fine.
    ssimonsen's Avatar
    ssimonsen Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Nov 1, 2009, 06:58 PM

    Oh thank you so much, I was so worried because I didn't remember seeing a light on when I was attempting to take the doors off.

    Now to figure out where the filters go? Sometimes I just don't get it...
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
    		  
    #6

    Nov 1, 2009, 07:06 PM

    The firlter should be in the duct or at the bottom end of your furnace.
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #7

    Nov 1, 2009, 09:05 PM
    If you have a single common return air grille, the filter may be behind it.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Diagnostic light flashing 3 1 on Bryant gas furnace. [ 2 Answers ]

Bryant gas furnace 14 yrs old flashing 31 on diagnostic led

Bryant model#310AAV042090ACJA Gas furnace LED light off [ 5 Answers ]

Hi, I have a Bryant model#310AAV042090ACJA Gas furnace. The system just won't turn on. I checked and the LED light is completely off. Turned power off to system, gas off, waited couple minutes, turned back on; nothing - won't turn back on. Strange thing is that at night it did not work, then in...

Bryant furnace won't light [ 1 Answers ]

We have a 13 year old bryant high eff furnace and the piolt light went out it says it has an auto start ---how do we go about making it light?

Bryant gas furnace won't light [ 1 Answers ]

I have a Bryant gas furnace that won't light. It starts its normal cycle with the inducer turning on, then the gas but the gas never ignites. It will do this three times then stops.

Bryant 373LAV Horizontal Gas Furnace will not light [ 1 Answers ]

Hello All, My Bryant gas furnace will not light. It will go through the motions like it wants to run but it never lights, nor does the fan run on the auto setting; only on the manual setting. It is also on some sort of time delay; if the thermostat is set higher than room temp. the furnace...

View more questions Search