Ask Experts Questions for FREE Help !
Ask
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #41

    Nov 25, 2008, 02:16 PM
    9. Radiator and Heater Hose Replacement

    Replace radiator and heater hoses every 4 to 7 years. Ruptured hoses are a prime cause of aluminum block engines overheating, often resulting in warped heads, blown head gaskets, and damaged valves.

    1. Drain coolant.

    2. Remove hose clamp. Vise grips or standard hose clamp pliers work best. Don't waste your money buying spring-loaded hose clamp pliers (i.e. those with a cable)--the head is too large, in practice, to be any good. They look like they'd be great for getting into tight places; however, they are virtually useless.

    3. Twist hose and see if it will come loose. If not, take a knife and cut the hose laterally along the nipple.

    4. TRICK: Lightly coat the nipple with radiator hose grease (AutoZone), silicone grease, or white lithium grease. This prevents corrosion, allows easier positioning of hoses, and makes it much easier to remove hoses next time.

    5. Install new hoses, clamps, and refill with coolant, following the manufacturer's procedure to eliminate air from the system.

    6. Start engine, allowing it to reach normal operating temperature, and check for leaks.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #42

    Apr 2, 2009, 06:16 AM
    Wip
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #43

    Apr 2, 2009, 07:34 PM
    Wip
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #44

    Apr 8, 2009, 10:28 AM
    8. How-to Replace Rear Wheel Bearing/Hub Assembly on a 1996 thru 2001 Ford Taurus and Mercury Sable

    The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS. Wheel bearing noise typically develops around 100,000 miles.


    1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

    2. Remove brake drum (parking brake must be off).

    3. Remove grease cap from hub.

    4. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g. OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

    5. Remove wheel bearing/hub assembly from spindle.

    6. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft. replace grease cap, and button everything up.


    The procedure above is similar to that used on many FWD vehicles. Obviously, sizes and torque specs will differ and some nuts may require "staking" or cotter pin replacement.

    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #45

    Apr 25, 2009, 04:44 PM
    Wip
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #46

    Apr 29, 2009, 03:14 PM
    13. How-to Stop Vacuum Hose Leaks

    Heat and ozone cause hoses to deteriorate and leak, over time. Once a vacuum hose is disturbed, particularly on older vehicles, it's prone to leak. This is particularly true on air conditioner vacuum hoses, which control diaphrams going to blender doors, where even small leaks can be disastrous.

    Here's a possible solution to air vents not working properly. Separate the vacuum lines and carefully service the connections with silicone grease. This will help to recondition and restore the seal. Obviously, you must use common sense and not apply too much and plug openings.

    An excellent product to use in this situation is Motorcraft Silicone Brake Caliper Grease and Dielectric Compound (XG-3-A). It's available at your local Ford or Lincoln/Mercury dealer. It's amazing the number of other applications this product can be used for; e.g. lubricating O-rings, rubber gaskets, disk brake caliper pins, radiator and heater hoses, plus using it as a dielectric compound for weatherizing battery and starter terminals and cables, main grounds, main ECM ground, ECM connectors, coils, spark plug connections, coating spark plug porcelein, and tail and brake lights. This product also helps prevent wet starting problems in seemingly small, but significant, ways. I mention these other applications, so you won't feel like you are spending money on a product with limited use. Attention to detail makes a big difference when dealing with vacuum hoses. Frequently, it's the difference between a system working or not working.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #47

    May 8, 2009, 01:58 PM
    Wip
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #48

    Jun 17, 2009, 07:03 AM
    25. After Clearing Codes, How Many Miles Do You Need To Drive Before You Can Have The Car Inspected?


    It's not an issue of miles--it's a function of drive cycles. Some drive cycles require a cold start, warm up, and a certain number of miles at a certain speed. So, there's no set answer. It depends on the year, make, and model of the car, along with the specific trouble code.

    After a code is erased, the computer "monitors" conditions, until the drive cycle has been completed. Then, it "resets" the monitors, making it okay for inspection. There's no way to manually reset the monitors.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #49

    Jul 3, 2009, 09:06 AM
    53. Clutch Pedal Maintenance

    Here's a preventive maintenance step to restore silky-smooth clutch action:

    1. Remove cotter pin and clutch pivot pin.

    2. Clean pin and hole of dirt and old grease.

    3. Lubricate pin with synthetic grease with moly. Valvoline SynPower Grease and Amsoil Synthetic Heavy-Duty Grease NLGI #2 (GHD) are excellent choices.

    4. Install pivot pin, along with a new cotter pin.

    You'll appreciate the "like-new" smooth action.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #50

    Aug 7, 2009, 09:24 AM
    10. How-to Replace Front Sway Bar Bushings on Ford Tauruses and Mercury Sables


    1. Measure the diameter of the sway bar with a Vernier caliper. It needs to be exact; e.g. 13/16" or 20.5 mm. Sway bars come in many different diameters. If you don't have a Vernier caliper, use a strip of paper to carefully determine the sway bar's circumference. Then, use the formula Diameter = Circumference/3.1416.

    2. Purchase a set of Energy Suspension Polyurethane Sway Bar Bushings. I selected 9.5107R (non-greasable) for my 2000 Taurus, with a 20.5 mm diameter sway bar.

    3. Place car on jack stands, located under the rocker panels. Remove both front wheels.

    4. Place a floor jack under each side of the subframe.

    5. Disconnect both sway bar links from the sway bar (Very important). If you don't, the old U-brackets will bind on the mounting bolts.

    6. Lower the subframe 1 inch, by losening the rear 18 mm bolts.

    7. Remove 13 mm bolts (4) mounting the U-bracket to the subframe.

    8. Pull the sway bar out enough and use an air cut-off wheel to cut through the old U-brackets and bushings length-wise. They are incredibly tough--don't waste your time trying to use an air chisel. Then, pry off the old brackets.

    9. Clean sway bar with brake cleaner and grease the mounting area with silicone grease (with Teflon) that comes with the bushings.

    10. Coat inside of each bushing with silicone grease, spread the bushing (slit facing forward), and place over the sway bar.

    11. Place new U-bracket over each bushing, install spacers under the front portion of the U-bracket, and tighten 13 mm mounting bolts (4) 25 lb.-ft.

    12. Raise subframe with the floor jacks. Tighten subframe bolts 66 lb.-ft.

    13. Attach lower portion of sway bar link to the sway bar. Tighten sway bar link nut (18 mm) 40 lb.-ft.

    14. Mount front wheels and tighten lug nuts 90 lb.-ft.

    15. Lower car and test drive. Handling should be dramatically better and quieter.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #51

    Aug 13, 2009, 08:27 AM
    3. Black Smoke

    1. If a diesel smokes, under any conditions other than full throttle or high load, something is wrong. Generally, too much fuel is being injected. At idle, or normal operating conditions found in the midwest of the U.S. and Canada, diesels shouldn't smoke.

    2. Check engine oil level--ensure it's filled to the top line and that the oil and filter have been recently changed. Since this often affects fuel pressure (Ford), begin by ensuring it's properly filled.

    3. Black smoke is usually a signal that there's too much fuel, not enough air, or injector pump timing is off. One of the most common causes is an air inlet restriction. The cause may be a dirty air filter, a collapsed intake hose, or an exhaust restriction.

    4. Check air filter--ensure it has been changed recently (every 5,000 miles).

    5. Check fuel injectors. Leaking injectors create an overly rich air/fuel mixture and cause black smoke. Take the valve cover off and look at the exhaust part of the injector, when it is running. Each time the injector fires, you should see oil exhausting from it. If you see oil coming out, then the injector is good. When replacing a bad injector, take the glow plug out and crank the engine to get any oil out of the cylinder. If you don't, you could hydro-lock and bend a rod.

    6. Check turbo for carbon build-up and bent turbine blades. This ties into exhaust restriction.

    7. Purge fuel filter or fuel separator of water. Do this at least monthly--daily, if necessary. Water can be a big problem with diesels. Watch for and treat bio-organisms.

    8. Look into a commercial diesel fuel additive, which is available at most large truck stops. Try and find one that is pure biodiesel, intended to be mixed in the tank at a B20 or less rate. Look for the words "naturally produced oil" or "biodiesel" on the side of the can listing ingredients. Properly mixed, it will reduce the amount of smoke an older, worn engine produces.

    9. Once you isolate and fix the problem, use full-synthetic heavy duty diesel engine oil (HDDO). Installing a by-pass oil filter makes using top-quality synthetics very cost effective, when integrated with a used oil analysis (UOA) program. All engines run better on synthetics, particularly turbo diesels. Besides significantly improved engine life, turbo life, performance, and gas mileage, synthetics promote easier starting, by allowing increased cranking speed. This last factor is particularly important in cold weather. Synthetics are also easier on batteries and starter motors. Finally, many diesel engines smoke dramatically less with synthetics. Anyone who has a turbo diesel and doesn't use full-synthetic HDDO is asking for trouble.



    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #52

    Aug 14, 2009, 09:39 AM
    4. Cavitation, SCA and Diesel Engine Cooling Systems


    The presence of a few tiny bubbles, some so small that you need a microscope to see them, can destroy a diesel engine. Cavitation is a problem that has plagued diesel engine owners for years, which is the formation and collapse of air bubbles on the outside of the cylinder walls during combustion. It does not apply to dry-liner engines. Repeatedly, these air bubbles implode against the liner's surface. It erodes the cylinder liner, ultimately penetrating the combustion chamber and ruining the engine.

    Cavitation is aggravated by vibration of the cylinder liner. Movement of the piston causes the liner to vibrate at a high frequency. When the liner vibrates, bubbles are formed in water passages next to the liner. These bubbles then implode against the cylinder liner. The implosion of the bubbles ultimately forms pinholes in the liner.

    Understanding Cavitation

    In elastic media, such as air and in most solids, there's a continuous transition as a sound wave is transmitted. In non-elastic media, such as water and in most liquids, there's continuous transition, as long as the amplitude or "loudness" of the sound wave is relatively low. As amplitude increases, however, the magnitude of the negative pressure in the areas of rarefaction (pockets of low pressure) becomes sufficient to cause the liquid to fracture, causing cavitation.

    Cavitation bubbles are created at sites of low pressure, as the liquid fractures or tears, because of the negative pressure of sound waves in the liquid. As wave fronts pass, cavitation bubbles oscillate under the influence of positive pressure, eventually growing to an unstable size. Finally, the violent collapse of the cavitation bubbles results in implosions, causing shock waves to be radiated from the sites of the collapse. The collapse and implosion of many cavitation bubbles, throughout an ultrasonically activated liquid, results in an ultrasonic effect. Temperatures in excess of 10,000 degrees F. and pressures in excess of 10,000 psi, are generated as cavitation bubbles implode.

    Effects on Engine

    Air enters the system through leaks or through a faulty radiator cap. Leaks reduce cooling system pressure and increase the potential for bubbles to form in the coolant. These bubbles will eventually increase pitting. Water pump impellers and housings can be victims of cavitation, caused by low system pressure or by air trapped in the system. Cavitation can also damage radiators and heater cores.

    Preventing Cavitation

    Since cavitation cannot be completely prevented, Supplemental Coolant Additives (SCAs) are necessary to provide a continuous protective coating on the metal surfaces of the cooling system. This coating aides in controlling and limiting engine damage.

    The most important way to control cavitation damage is to keep the cooling system clean by periodically flushing it. Using distilled water, combined with flushing agents, will scrub the system of impurities, scale, or other build-up, allowing for a "second chance" when refilling with a 50/50 mixture of auto maker approved antifreeze and distilled water.

    When servicing the cooling system, always check for leaks or faulty pressure caps. These conditions can cause air leaks, reduce operating pressure, and allow bubbles to form.

    Add 8 to 10 ounces of SCA every 15,000 miles, testing it with Fleetguard strips every other month. Completely drain and refill the cooling system with a 50/50 mixture of approved antifreeze and distilled water every 30,000 miles. Be sure to remove the hex-head drain plugs, located on each side of the engine block, after disconnecting the negative battery cable. This is a must on diesel engines. Cavitation must be taken very seriously.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #53

    Aug 31, 2009, 01:32 PM
    14. How-to Remove and Install a Transmission Range Sensor (TRS)

    The Neutral Safety Switch is part of the TRS.


    Removal:

    1. Disconnect negative battery cable.
    2. Place gear selector in Neutral (N).
    3. Remove air cleaner and air cleaner outlet tube, if necessary.
    4. Disconnect TRS electrical connector.
    5. Remove manual control lever from transaxle.
    6. Remove TRS retaining bolts (2).
    7. Remove TRS.

    Installation:

    1. Ensure gear selector is in Neutral (N).
    2. Install TRS and loosely install both retaining bolts.
    3. Align TRS slots using TRS Alignment Tool.
    4. Tighten TRS retaining bolts 9 to 12 Nm (80 to 106 inch-lbs.) and remove tool.
    5. Connect TRS electrical connector.
    6. Install transaxle manual control lever--tighten 11 to 16 Nm (98 to 141 inch-lbs.).
    7. Install air cleaner outlet tube and air cleaner.
    8. Connect negative battery cable.
    9. Check for proper operation with parking brake on. The engine should start only in Park (P) or Neutral (N).


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #54

    Sep 13, 2009, 08:17 PM

    2. Diesel Smoke Summary: Black, White, and Blue


    Exhaust gases from a diesel engine should be colorless. Smoke of any color is a clue that it's not running properly. Here's what exhaust smoke tells you:

    • Black smoke is a sign of engine overload, restricted air supply, or malfunctioning injector. For some reason, excess unburned fuel is being blown out the exhaust. Black smoke is usually a signal that there's too much fuel, not enough air, or injector pump timing is off. One of the most common causes of this condition is an air inlet restriction. The cause may be a dirty air filter, a collapsed intake hose, or an exhaust restriction.

    Installing a power chip can cause engine overload (boost gauge maxing out), black smoke, and engine shut down. I usually recommend using the standard OEM chip. On a diesel engine, injecting more fuel will result in more power--up to a certain point. This is almost opposite of a gasoline engine, where adding fuel and richening the mixture excessively will kill performance and lower power. A diesel engine is totally different. As you add more fuel and richen the mixture, power output will continue to climb, until the point that there is so much fuel that much of it is unburned (or partially burned black smoke) and then the power increase will taper off. Before the power increase drops off dramatically, however, you'll be facing another limiting factor--exhaust gas temperature (EGT). Adding more fuel makes more power, but it also raises EGT. If you add too much fuel and exhaust gas temperatures get too hot, then you can seriously damage your engine. Hence, an important reason to only use full synthetic HDDO. Full synthetic HDDOs also help control or eliminate black smoke, in many situations, by allowing the engine to run much more efficiently, even when overloaded.

    • White smoke is a sign of water vapor or fuel that has been atomized, but not burned. Water vapor may be present in the fuel, or water may be leaking into the cylinders from the cooling system. Also, air in the fuel can cause white smoke. White smoke usually occurs when there is not enough heat to burn the fuel. The unburned fuel particles go out the tailpipe and typically produce a rich fuel smell. It's not unusual to see white smoke in the exhaust, during cold weather, until the engine warms up. Bad glow plugs (burned out, coated with carbon, or not receiving proper start-up voltage) or a faulty glow plug control module can cause white smoke on engine start up. Low engine cranking speed may also produce white smoke. If white smoke is visible after the engine has warmed up, the engine may have one or more bad injectors, retarded injection timing, or worn injection pump. Low compression can also be a source of white smoke.

    • Blue smoke forms when the engine's lubricating oil is being burned, indicating worn piston rings, valve guides, or seals. Also, the oil can come from an air filter overfilled with oil or an overfilled crankcase.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #55

    Sep 18, 2009, 01:15 PM
    5. Diesel Fuel and Cold Weather


    Wax, naturally found in diesel fuel, begins to form crystals, as the temperature drops. The cloud point is the point at which crystals form. Eventually, crystals clog the fuel filter and starve the engine of fuel or prevent it from starting.

    Traditionally, one solution is to use #1 diesel fuel, which is diesel fuel diluted with kerosene. There are several disadvantages with using #1 diesel fuel, despite its advantage in low-temperature operations. First, the energy content is about 95% of #2 diesel fuel, resulting in less horsepower and reduced fuel economy. Second, the kerosene used in #1 diesel fuel provides less lubrication for the fuel distributor and fuel pump, increasing the likelihood for wear.

    There are products on the market, such as Amsoil Diesel Recovery, that dissolve the wax crystals that form when diesel fuel has surpassed its cloud point. It will liquefy gelled diesel fuel and thaw frozen fuel filters. Since diesel fuel quality varies wildly from one filling station to another, low-quality fuel can have cloud points as high as 40 degrees F.

    Check these type of products out. They can reduce the cold filter-plugging point (CFPP) by up to 34 degrees F, in ultra-low-sulfur diesel fuel (ULSD), and up to 17 degrees F, in biodiesel. They also lower the fuel's pour point. Emergency diesel fuel treatments may help you avoid a costly towing charge.

    Steps to improve cold weather diesel starting:

    1. Use the appropriate winter viscosity of full synthetic HDDO for your vehicle.

    2. Add Amsoil Diesel Concentrate Plus Cold Flow Improver (DFC) to diesel fuel in the winter, prior to crystal formation. Use this product throughout the winter months, starting at 40 degrees F.

    3. Add Amsoil Diesel Recovery Emergency Fuel Treatment (DRC) to diesel fuel, after crystal formation.

    4. Install a engine block heater for temperatures below -25 degrees F.

    5. Ensure both batteries are fully charged and the battery terminals and cable connections are clean. Apply dielectric grease.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #56

    Sep 19, 2009, 07:03 AM
    Wip
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #57

    Sep 26, 2009, 09:14 AM
    12. How-to Perform Electronic Air Temperature Control (EATC) On-Board Diagnostic Tests on Many Fords and Mercurys


    NOTE: Intermittent (run time) trouble codes will be deleted after 80 ignition cycles.


    The Remote Climate Control (RCC) module is capable of displaying both self-test faults and intermittent (run time) faults on the Integrated Control Panel (ICP). To obtain these codes, perform the following EATC on-board diagnostics test:

    . On-board diagnostics should be run in ambient temperatures between 50 and 90 degrees F. Record all Diagnostic Trouble Codes (DTCs) displayed during diagnostic test mode.

    . Turn ignition switch to RUN position.

    . Push both OFF and FLOOR buttons simultaneously; then, press AUTO within two seconds.

    . The test may run as long as 30 seconds, while the display will show a dashed line in the center of the display window.

    . After about 20 seconds, a DTC will appear in the display. The self-test is completed when 888 appears in the center of the climate control display window of the ICP.

    . To exit the self-test and retain all intermittent DTCs, press the "-" (cooler) side of the TEMP button. The RCC module will exit the self-test and retain all intermittent DTCs.

    . Always exit the self-test, before powering the system down (system turned off).

    . Refer to a DTC Index for additional help. Here are several common self-test faults:

    024--A/C Electronic Blend Door Actuator Failure
    030--In-Car Temperature Sensor Short
    031--In-Car Temperature Sensor Open
    040--Ambient Temperature Sensor Short
    041--Ambient Temperature Sensor Open
    050--Sunload Sensor Short

    . Some heating and air conditioning control problems are solved just by running the self-test.


    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #58

    Oct 12, 2009, 06:28 PM

    26. Engine Misfires


    Most common engine misfires can be solved by:

    1. Replacing platinum spark plugs with the exact ones (same brand and part no.) that came in the vehicle and ensuring they are properly gapped. If the vehicle came with single platinum plugs, changing them to double or quadruple platinum plugs can cause misfires, particularly if the gap is different. Therefore, I recommend using single platinum plugs and changing them every 50,000 miles. On FWD V-6 engines, be sure to change the rear plugs, despite the hassle.

    2. Applying dielectric grease to the spark plug's porcelein and electrode.

    3. Changing coils and coil packs, if changing spark plugs did not solve the problem. Bench testing coils is not reliable, since most break down under load (heat). Therefore, be sure to change coils and coil packs every 120,000 miles or 10 years, whichever comes first. Apply dielectric grease to terminals.

    4. Replacing Ignition Control Module (ICM). These problematic components should be replaced every 120,000 miles or 10 years, whichever comes first. Bench testing ICMs is not reliable, since most break down under load.

    5. Ensuring coil-on-plugs are squarely centered on the plug's electrode.

    6. Changing spark plug wires every 80,000 miles. Regularly, wipe down plug wires with silicone spray, being very careful to keep it away from oxygen sensors.

    7. Checking for intermittent codes that did not trigger the Check Engine Light.

    8. Checking engine compression and looking for intake manifold leaks, in extreme cases.

    9. The link below, provided by kitch428, covers a number of advanced techniques for diagnosing engine misfires:

    Determining the missing elements in misfires - Misfires occur when the combustion process is incomplete, so you need to find what's missing. - Motor Age - Automotive training, certification & parts



    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #59

    Oct 29, 2009, 08:22 PM

    30. Toyoto to Begin Requiring 0W-20 Synthetic Engine Oil

    Driven by increasingly stringent emission and fuel economy standards, Toyota has informed its dealers that the company will begin requiring SAE 0W-20 synthetic engine oils in new Toyota, Scion and Lexus vehicles over the next several years. Other OEMs are expected to follow suit by 2011. Among the benefits cited by Toyota are enhanced protection at high and low temperatures, improved fuel economy and reduced engine deposits. In addition, Toyota is reportedly studying increasing oil drain interval recommendations to 10,000 miles.
    TxGreaseMonkey's Avatar
    TxGreaseMonkey Posts: 16,761, Reputation: 5597
    Uber Member
     
    #60

    Nov 19, 2009, 09:07 AM

    15. How-to Change Front and Rear Bulbs on a 2000 and Later Ford Taurus


    Front:

    1. Remove mounting bolt near the front grille (8 mm).

    2. Pry up both retaining slides (look for two rubber-coated tabs), located on the rear of the headlight housing, with a screwdriver.

    3. Pull the housing outward, disconnect the electrical connector from the headlamp bulb, and remove the housing from the vehicle.

    4. Remove and replace the headlamp (Sylvania 9007) and amber turning signal (Sylvania 3357), after cleaning the connectors with WD-40.

    5. Button things up.

    6. Adjust headlamps with the vehicle parked level, gas tank half full, and nothing in the trunk.


    Rear:

    7. Remove parcel restraining web and tie-down, pull back trunk liner, and remove five nuts (11 mm) securing the tail light cover with a nut driver.

    8. Remove and clean tail light cover.

    9. Remove old bulbs--back-up light (Sylvania 921) and tail light (Sylvania 3057). Spray and clean connectors with WD-40.

    10. Snap-in new bulbs, replace cover, and button things up.


    Don't touch bulbs with your fingers because the oil from your skin could cause it to overheat and fail prematurely. This is particularly true of headlamp bulbs.


Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search


Check out some similar questions!

How to troubleshoot, repair & maintain toyotas 4 runner motor 3.0 1992 [ 2 Answers ]

How to troubleshoot, repair & maintain toyotas 4 runner motor 3.0 1992 thanks

How to troubleshoot, repair & Maintain 92 Accord [ 1 Answers ]

I replaced my distributor on 92 accord following you instructions. However, towards the end, it says that I need to read section C and D to precisely set idle speed and ignition timing. Can you tell where I can find those Sections? Thanks.

HOW TO TROUBLESHOOT, repair and maintain mustangs 1992 [ 2 Answers ]

I really appreciate your help

Heating & Cooling Maintenance, Repair & Troubleshooting FAQ from NortherHeat [ 57 Answers ]

Check out these tips and explanations, below, from our Heating and Cooling Expert. Of course, you're also welcome to post questions to this board for more information: Just click the "Ask about Heating & Air Contidioning" button at the top of the page.


View more questions Search