Ask Experts Questions for FREE Help !
Ask

Concerning Deere L130

Asked Dec 18, 2010, 11:29 PM — 3 Answers
I am now looking at the carb on an L130 23hp Kohler engine. There may be an issue with the fuel solenoid that mounts flat on the top of the carb. Is it possible to detach the solenoid from the carb without having to have replacement gaskets on hand for re-assembly. What exactly is the function of the solenoid in relation to fuel flow? Could this solenoid stick the way a starter solenoid sometimes does?

Search this Thread
Share |
3 Answers
crigby's Avatar
crigby Posts: 3,747, Reputation: 466
Outdoor Power Equipment Expert
  
#2

Dec 21, 2010, 04:55 PM


Hi,
The manual can be found at the link below and fuel system part starts at page 35. The fuel shutoff solenoid is at the bottom of the carb. The plate at the top is for service, the solenoid is at the bottom with the ground wire attached at the top. Care will preserve the gasket and allow reuse. The manual can be found at:
Kohler Manuals
And you scroll down to the CV17-745 Service Manual - TP-2450-B. It is also at:
"K&T Parts House Lawn Mower Parts and Chain Saw & Trimmer Parts"
And scroll down to the the CV`7 CV18, etc. Manual.
Peace,
Clarke
Helpful  (1)
johndeere52's Avatar
johndeere52 Posts: 9, Reputation: 10
Junior Member
  
#3

Dec 21, 2010, 10:58 PM
Comment on crigby's post
Quote:
Originally Posted by crigby View Post
Hi,
The manual can be found at the link below and fuel system part starts at page 35. The fuel shutoff solenoid is at the bottom of the carb. The plate at the top is for service, the solenoid is at the bottom with the ground wire attached at the top. Care will preserve the gasket and allow reuse. The manual can be found at:
Kohler Manuals
And you scroll down to the CV17-745 Service Manual - TP-2450-B. It is also at:
"K&T Parts House Lawn Mower Parts and Chain Saw & Trimmer Parts"
And scroll down to the the CV`7 CV18, etc. Manual.
Peace,
Clarke
Have gotten that far and even found the manual. Solenoid works on bypass so I may have jiggered up the ignition switch when I tore it apart. New one will cost less than 20 so I think I've almost unscrewed the pooch. Thanks 4 pointers. They helped
Helpful
crigby's Avatar
crigby Posts: 3,747, Reputation: 466
Outdoor Power Equipment Expert
  
#4

Dec 22, 2010, 07:38 AM


Hi,
Parts can be easily looked up at JDParts at:
http://jdpc.deere.com/jdpc/servlet/c...ageServlet_Alt
I always use the Sectional Index, and under Electrical it is a #GY20074.
Peace,
Clarke
Helpful
Not your question? Ask your question View similar questions
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

John Deere L130 [ 9 Answers ]

My John Deere L130 will start but only run for a second. I can do this several times at full throttle and full choke and it only runs for a second or two. If I retard the throttle to 50% it will run a few seconds longer but that's it. I know this must be a fuel flow issue but the filter liooks...

John Deere L130 [ 0 Answers ]

Does anyone have an electrical diagram and an engine diagram for the L130 Koeler 23 hp?

John deere l130 mower [ 2 Answers ]

The fuse blows when I engage the mower deck New battery new fuse new switch I don't know

John Deere L130 [ 3 Answers ]

Subject: John Deere L130 Mower Is there a way to adjust the drive belt on this mower? Not the mowing deck belt but the drive belt. Thanks in advance for any help. Jimmy

John Deere L130 [ 1 Answers ]

Concerning my 3yr. Old John Deere riding mower L130 w/23HP Kohler engine. The pedals that you depress to make it go forward and backwards seem to have lots of slack or looseness in them. My neighbor has the same machine and his has no looseness and respomds to foot movement quickly. Can this be...

View more Tools & Power Equipment questions Search