Search:
Type: Posts; User: mgliue
Search:
Search took 0.00 seconds.
-
It depends of what are you talking about...
-
Yes, it can be moved. Just to be careful where you decide to install. Some things you must take care is for example that the new place must not be a sunny place, or near a heat source like the stove...
-
I think that MKLINE is not talking about the same thing than us. GRETCHEN4 is asking about a WALL HEATHER, not a WATER HEATHER!! Anyway, better to read again pal... There is not a rod in a wall...
-
When was the last time you call somebody for service? Normally you are supposed to do that once a year. If not, dust and others can affect the combustion and the resulst can be dangerous. Check the...
-
Did you already checked that the option FAN in your th is at AUTO position? In is not just switch to auto. Depending the kind of furnace you have can be some others problems concerning the fan...
-
-
Yes there is one. The heat exchanger is a part that separes the cflame side from the clean warm air, just to explain you better. If you do not see it is just beacause you don't know what it is, but...
-
Why you think it is restricted? If it is true you can use a compressor, firt of all, buy you a good protection mask and safety glasses, cut the power and gas to your furnace and blow air into the...
-
Be careful. Close the manual gas valve, put the fan on, light a long match and introduce it in each burner with the blower running. If your match "dies" your furnace is "dead". Your heat exchanger...
-
If you do not have the book can you tell me your th model? It depends of which oone you have there are differents ways.
-
Very important: Shut off the main switch of your furnace before opening your door.!
-
Open de furnace door, take a look to the connections to the electronic board. I suppose that your new th, is labeled. So if example if your orange in the board is connected to W is going to be...
-
Yellow to Y, green to G, white to W and red to R. Easy pal
-
And what about the pump? Can you find it? Normally is a red device installed between two flenges and it has an electric wire connectes, one make possible is Grunfoss...
-
I must go now, I'll be back in 2 hours, I don't forget you...
-
Do you know if you have a pump in the system< sometimes the pump stops running and the water doen't circulate. Also... is there a manometer or gage to see the pressure?
-
Do you have a recirculation pump I your system?
-
Your furnace needs to be cleaned.When was the last time you did it. Im not talking about just your bro in law coming to clean. A good expert tech. How old is the machine? Do you make maintenance...
-
OK, first give us more information about your system. Is a water tank, like a cylinder that produces domestic hot water an also heats radiators , is it made by JSW... or who? BTU? OK pal? More info...
-
Don't try to take out the main gas valve until you are sure that the other 2 things are OK, If you have to do it you must replace the control and I suppose that you actually have an old MGV, so you...
-
You have to check first : the quality of the pilot flame, often the pilot is dirty and the flame is not enough to heat the thermocouple. If you see that you have a small, yellow or orange pilot...
-
Is it possible for you to send me a picture of your motor? My e-mail [email protected]
-
PLEASE... EXPLAIN ME BETTER WHAT IS YOUR POINT... brand, year, why, what are you trying to do...
-
Be careful! Do not use the furnace anymore... a cracked exchanger allows combustion products pass into your room CO included. So I suggest you to replace your furnace TODAY. There is no way to repair...
-
MMMM. Please, start by the beginning... why did you decide to change the limits, try to explain better your problem... what is an IDM for you? Thanks
-
Oh I'm sorry, you said that if the thermostat asks for heat the fan doesn't run, sorry... mmmm so the electronic board is not sending the signal to the fan to run. There are some relays that are...
-
Hi, there is no problem. If you set on the fan is going to run. To put the fan on is just for create circulation into fthe house. The system is going to take the room air from the return and send it...
-
Forget the thermocouple, the pilot is on. Do not try to operate the furnace by-passing the door switch!! You can be injured. Look for 24 volts, your transfo can be out. Because if you have a...
-
First check if the pilot is working properly. If you have a nice and powerful flame. Sometimes the connection to the pilos is loose and the flame is smaller than required, also it can be some dirt in...
|