Search:
Type: Posts; User: maxpinck1
Search:
Search took 0.00 seconds.
-
Which supplements or name brand is the best to use as far as their no, creatine, anabolic and any other supplements? They all have that catchy headline about science proven, but I wonder is there a...
-
If you trace the upper radiator hose from the radiator to were it stops, that should be your thermostat, remember that when you finish to make sure you blled the system to get all the air out.
-
He is right about the dealership, but if you still want that info:
Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
On 1988-91 Preludes...
-
Check your valve cover gasket, pcv valve and oil pan gasket. You can also clean the engine off, put some dye in it and use a blacklight to see were it is coming from.
-
I agree with txgreasemonkey, who did your ring and valve job?
-
Start with a cold air intake and exhaust. You can get these products at a real good price from stores like pep boys or the internet, you can also try a programmer or a chip for starts and just take...
-
Check for corrosion not only around the terminal, but the cable to under the coating of it.
-
It is possible it can be the computer or the harmonic balancer, ignition system like the plug wires could be broken some were.
-
Where did you purchase this tool from.
-
-
The hanes or chilton manual go in detail for your vehicle, I tried attaching the section you need, but I am having problems with it.
-
What is the maximum time have anyone had to bleed the clutch on a 98 ranger
-
True and that's how I end up changing everyhting that was posted, I use my scanner, autozone and advance.
-
It's a chance it could be a short somewhere or the switch could be going bad, also check the relay, when it gets short out it disconnect itself and after a while reconnect, which makes it work on and...
-
This might help, but yes the hanes are chilton manual have a lot of info in it.
-
It will probably be wise to get it checked for the knock and thee lost of oil. I don't know if you have hydraulic lifters are not, but some can be adjusted. Check with a mechanic you really trust...
-
I have posted about this problem before. I changed the maf, plugs, all o2 sensors, fuel filter and check for vacuum leaks. It stopped after each one, but my wife and I notice that it comes on when...
-
I have a 03 yukon xl with a 5.3, went the check engine light first came on the code was p0171 and p0174. I changed both of the pre o2 sensors, the check engine light went out and came back on after...
-
The last powertrain code for your car is P3497. Could the mechanic mean P0506.
-
I will also help with your car problem, I have access to a code manual.
-
What I meant about the block being cold and the fuel delivery, is the computer is always going to correct for a warm block, sorry if I confused you.
-
It could be one of your temp sensors, there is on for the computer and one for the coolant. What it could possibly doing is the computer is sending enough fuel to crank it based off the temperature...
-
Is it a power window or manual, if it is a power window it could be the reuglator
-
I also have the diagram for other controls, hope this help.
-
Can your mechanics check the fuel system, fuel pump, filter, delivery and for possible restrictions. It sounds like when that fuel pump gets hot, it need to cool off before it starts back delivering
-
I agree with changing that cable for sure, also check to make sure it have a proper and clean ground, you can also check how much the starter is drawing and the put out from the battery and...
-
Check for a vacuum leak, also at a normal idle without giving it gas, do it have the same problem or it is at a normal idle. You can check for a vacuum leak with a spray bottle with water in it and...
-
I just replaced the master cylinder, the truck cranked up at first and after I shut it off, it wouldn't start. I checked the fuses and 2 fuses were blown after replacing the fuses, the truck still...
|