Search:
Type: Posts; User: dobiefloyd
Search:
Search took 0.00 seconds.
-
I figured out the problem. All 3 fuses were good for the low beams but the relay was bad. All 4 are under the hood in the fuse box... easy fix. 10 minutes, a test light, owners manual, and $35 for a...
-
What did you find as the cause of the problem? I'm having the same issue. Thanks.
-
I have a 2000 sierra with a 5.3 that surges when first started. I did have an idle control code (dont remember code number right now). Ideas?
-
What is the best way to conert from wood to gas and how do you get to the flu liner to hook it up when installing an insert?
-
The codes are p059 and p060, bank 2 sensor 1 and bank 2 sensor 2. I agree with you... I'm thinking an intake or bad injector. Any other ideas?
-
What model Honeywell stat is it?
-
Is this a new furnace instatll?
-
Inside the house? Or inside the condenser unit outside?
-
I have a 06 Chevy Express van 3500, 6.0L engine. Check engine light comes on with o2 sensor coming up on bank 2, sensor 1 and 2. I have peplaced both sensors and cleared the codes. That light came...
-
I have an old fuel oil furnace that will shut down after running for a bit. If you set the t-stat to say 75 and let it satisfy it the furnace will not come back on. If you turn the stat down before...
-
If it were mine I would try to bypass the skimmer line. Cut the skimmer line at the pump and hook up the vac there. If it works the problem is in the line. It does not fix the problem or locate the...
-
It's been a year since I posted that. Tha shaft seal was leaking and was replaced. When I was replacing it I cracked a glue joint on a PVC fitting. To find my new problem I ran a hose over all the...
-
I need to replace the abs controller on the truck, any tips? What will be involved?
-
I found the problem. The EGR tube goes up through upper plenum between coolant passages. After time the plastic burns through. By removing it and reinstalling it made it a big problem, drank coolant...
-
Fixed it. I adjusted the cable that goes to the drive box at the belt. Not sure what it does but it works great now.
-
I have a Honda HS55 snow blower that won't engage in 1st or second gear. 3rd and reverse work fine. I have tried adjusting a few cables but now luck.
-
I have checked for cracks but can't see anything visible. Can't find anything I did wrong?
-
All cylinders have water. I pulled the upper and it was full of coolant, it filled up as the car was running. All the torgue was right, 89in-lbs. I didn't have the specs for the throtle body so I...
-
I had to replace a lifter in my Bonneville (non supercharged) and now the engine hydro locks. Any ideas before I tear it apart again.
Car ran great for 10 minutes and then started running a little...
-
Follow up...
Sorryy, it is a 3.0L
I found the code and also found #5 dead.
Replaced the injector... all is well!
Thanks
-
What is code 26 on 89 dodge caravan
Thank you.
-
-
Other than the way it runs, no other problems.
It was a "toss a part at it idea".
Whatcha throwing?
But really, why won't the code stop coming up? Sensor is know to be good. The problem has...
-
-
Hey TXGM
Thanks for the help, this one has me a liitle stumped too!
What do you think about the computer? Is it worth throwing a used one at it?
Thanks
Ed
-
Anyway of adding an alternator? Or any other options? Magneto?
-
How do I get 12 volt power from my 3.5 horse briggs. I want to power up a head and tail light.
-
I have no dipstick and no slot in the filler hole. Any ideas? Fill to bottom of threads, Middle of threads?
Thanks
-
It is not that bad of a job, Just a few bolts and it should tap off with a hammer. Personally I would replace the whole hub, unless you have a bearing press. A complete hub is cost effective if you...
-
Yes I did. The wiring problem with the solder was on the sensor side of the plug. Another reason I replaced the sensor. The one replaced was a universal one so I wanted to make sure the wiring was...
-
Thanks TXGM.
I did replace it with an OEM part. A $225.00 OEM part.
-
Update-
I bought a scanner and erased the code.
The same code comes up within 15 miles of driving. The new oxygen sensor only changed where the call idles at, which is now correct. P0037 comes up...
-
Thank you
I just ordered a kit.
Ed
-
Where can I buy these? I popped my cap last night and my balls rolled down the driveway and down the road. I live on top of a hill and it was dark so I only have one ball left. True story.
Thanks...
-
What is the oil capacity of a 3.5 briggs? Also how do you know when it's full?
Thanks
-
-
Finally replaced the O2 sensor, seems to run fine. How do I clear the computer without a scaner? I disconected the battery but the light came back on.
-
Well I switched out the coils and no change.
Anyone have any ideas?
Thanks
-
Thanks for the response
I do not know anything about it, unless you are referring to reading the computer with a scanner? Would that explain my problem with jumping A&B together? Any thoughts on my...
-
No boom, just spray a little at a time an listen for a change in the engine. Let us know.
-
Any not worthwhile thoughts?
-
Any thoughts on the code and light problem? Not to railroad the question but could that be a compuer problem also linked to a bad signal to the ICM? I do agree that it is an ICM/coil problem but will...
-
Grab a can of carb cleaner and spray around intake manifold and fittings. Spray short shots at a certain area, wait a second or two and listen for the miss to disappear. Pretty easy, you will know...
-
Thank you
I bought a used ignition module and coils but only switched out the module not wanting to risk getting a bad coil since I knew the coils are fine. The car runs perfect when it is...
-
I have a 94 cadillac eldorado that stalls when driving and will immediately restart and run for 5 to 10 minutes and shuts down again. I replaced the ignition module with a good used one and no...
-
Porpiose I think? I replaced the shaft seal, stopped the leak. My filter still always has air in it and bubbles in the skimmer basket. It seems like I have been adding more water than normal the last...
-
My pool pump is leaking at the motor where the motor mounts to the pump. Is this a gasket?
-
Did you also hook up your zone motors? If the stat wasn't odds are good they never wired the zone motors.
-
Floor drain? Is this a 90% furnace. I have seen rusted cast traps that will drain in a days time. If it not producing condensation for a day the trap might be draing.
-
Sounds like or I mean smells like rats to me. Now how are they getting in there?
|