Search:
Type: Posts; User: rocky21
Search:
Search took 0.00 seconds.
-
I have a 42" jvc lt-42x579 flat screen TV and somehow it set its self back to the air setting and I need to change it to the cable setting so that my picture will come in right again. When I try to...
-
I have a fridgedare gas stove and its about 5 or 6 years old I guess, but anyway today I was going to clean it using the self clean feature. I removed the racks and closed the door and pressed the...
-
I agree ziebart is a good product. I have saw a lot of older cars that were ziebarted and they just don't have the rust problems like the cars that haven't been treated.
-
I've told you everything and I agree the installer should man up and take care of the problem, but after several phone calls and getting the same answer that he's pretty busy and doesn't have time...
-
I suppose your right, it just doesn't seem right that a new furnace should have so many bad parts in it. When he installed it he replaced the board once that was bad as well as the switch that is...
-
Thanks for all of the help everyone, I appreciate your efforts, but I really need to get this going so I think I'm going to first call goodman direct and tell them about my problem since it is under...
-
I'm not 100% sure on how to properly check the voltage, I do have a multitester, not real sure what setting to set it on or how to check it properly. And yes the furnace is less than a year old it...
-
I know and after spending so much money I'm just trying to save and fix it myself, I work on cars houses just about anything I can fix if I study it a bit. Should I get another ignitor and try that...
-
No I called the installer as was suggested, but it's a warranty issue and he doesn't have time to do warranty work for free, so its still not working. Just trying to get it back in working order.
-
Yes after it goes through the ignition cycle a couple times the light on the board does flash, it's a slow continuous blinking. And yes it does run fine after I manually light it with a bbq lighter.
-
Is there anything other than the board that would tell it to ignite?
-
I pulled it out and I can't see and bad areas on it, it actually looks like new, could it still be bad even though there isn't any obvious damage?
-
Yes you can manually light it every time with no problem.
-
I have a 80% GMH8 goodman furnace that won't ignite. I can manually light it when the gas valve opens and it will run fine and shut off like normal. The glow plug ignitor doesn't come on but a couple...
-
I can't tell you exactly where each screw is withoug actually seeing it, but there is probably a few screws that you will have to remove first, some may be hidden. Look around the edge of the panel...
-
I have determined that the problem lies with the glow plug ignitor. I did see it glow once when it was trying to cycle but as quick as it came on it went out and it seemed like it came on too early....
-
I would use a good quality undercoating,there are kits you can get that come with a spray wand that you can use to get up inside of hard to reach places. If you look around there are some places that...
-
Its been awhile since I took one of those apart, but I'm thinking after you remove any screws that you need to that the trim surroundthat goes around the guages and radio and such just snaps in...
-
I am a bodyman and you can try rubbing compound, just put a small amout on a soft rag and rub fairly hard and this should remove it (this can be bought in a small amount at you local auto parts...
-
I couldn't see the glow plug glowing. Yea the furnace was installed in July 08 but I'm not really thrilled with the installer because after he was finished he charged twice the quoted price and kind...
-
I tried it twice and no flame, I could smell the gas as it tried to cycle, then after awhile it just shut back down
-
The tube tees off and goes to 2 switches side by side
-
-
I'm not exactly sure what your calling a pressure switch. Are you referring to the switch behind the cover that is pressed in when the door is on?
-
No there is no flame at all
-
I recently had a GMH8 goodman furnace installed in the summer and after it was installed it fired right up, but now that I don't need the air and its time to use the furnace it won't ignite. It...
|