Thanks for any help that can be given.....
Whenever I press the flush lever on my toilet the toilet will flush, the bowl will fill and drain, and then the bowl will fill and drain another 2 more times before the tank begins to fill. So in effect my toilet flushes 3 times for every one time I press the lever. I don't have any other plumbing issues (that I know of) and as far as I can see it looks like all the parts in the tank are in good condition. Any ideas?

massplumber2008

I think it may be that you have TOO much water in the tank. I would have you start to fix this by first reducing the water in the tank.

If don't know how to reduce water level then please let me know what the inside of your tank looks like...the top pic. or the bottom pic...?

Also...tell me if any work has been performed on the parts in the tank....? That could be important here.....OR has it always been like this?? And also, how old...?

Get back to me...MARK

.

Attached Images

  

speedball1

Also let Mark know if you have a have a flapper with a float build into it. Regards, Tom

historicalficti

Thanks for the great diagrams, I'll compare them to my system and get back to you.

In regards to your other questions, I just bought my house in January and the toilet has been acting like this since then. I would guess that the internal parts are 3-7 years old based on condition. I don't know any history past that.

Thanks!

massplumber2008

OK...let us know what you can when you get home..and like Tom asked..check to see if the flapper has a float of some kind on it...?

Name on the toilet would help too...

Talk soon...MARK

historicalficti

OK, it's definitely the top diagram, the "400A". I didn't see a float on the flapper. I also didn't see your post until this morning, so I wasn't able to get the manufacturer name, sorry.

speedball1

No problem! You have a Fluidmaster ballcock. Answer Marks questions firs and then to lower the tank level, pinch the adjustment clip and move the float can down until the desirerd level's reached. The tank level should be 1 inch below the top of the white overflow tube. Good luck and let us know it it helped. Good luck, Tom

massplumber2008

Like Tom said....pinch the adjustment clip and slide it down to reduce the water flow if needed. As he said, should be about an inch or so below the overflow pipe.

If that is alright and water is set at about 1" below the overflow pipe....then this can be one of ther following:

1) They changed out the fill valve and the flapper and water level was set to within 1" of overflow pipe BUT, in your case water level should not have been set so high because say...your tank is a 3.5 gallon or similar and this triple flushes because flapper rides height of water column for too long. So here, reduce the water flow by pinching the clip and sliding it downward.

If that did not reduce the water enough to reduce flushes then you will need to shut the water supply to the toilet and then grab the VALVE BODY (see pic.) in one hand and the gray circular sliding clip (see pic....clip is across from the words ADJUSTABLE HEIGHT) in the other hand and pull UP on the clip (pulls up about 1"). Then push the valve body down an inch or so, then slide the clip back down into place (you will hear a CLICK sound to be sure it is seated) and turn water on and see if that hepled to reduce the number of flushes.

If that didn't improve dramatically and seems can go lower, just repeat the sequence just noted.

2) If these things don't work, may be time to purchase another flapper or two and try them out here. May just be the wrong flapper for your setup???

Adjusting water levels are so easy that you should play with this a bit....then if that fails try the universal flappers.

Let us know what you think...how things went so far....MARK

.

historicalficti

Hi. So my toilet is a Kohler. The adjustment clip was down almost all the way so I moved the valve body down and got it to fill and drain only once! I really do appreciate everyone's help on this. I do have another question now: Since I moved the valve body down the Critical Level line is about 2" BELOW the top of the overflow pipe, is this important? (hence the word "critical") It seems to me that my options are to 1) cut the pipe down below that line or 2) try changing flappers and thereby be able to move the valve body up, or option 3) is.....??

massplumber2008

As long as the height of the overflow pipe is below the level of the hole in the tank for the toilet HANDLE, then you are all set!!

The overflow pipe must be set below this hole or if the fill valve fails water will come out the toilet handle hole and flood the bathroom before going into the overflow pipe...a bad thing!!

You could also change the flapper, but if toilet is flushing properly and removing all solids, then I say you leave well enough alone!!

Good luck!!

If my answers helped please RATE THIS ANSWER. Thanks
.