At Ask Me Help Desk you can ask questions in any topic and have them
answered for free by our experts. To ask questions or participate in
answering them you must register for a free account. By registering you
will be able to:
Get free answers from experts in any of our 300+
topics.
I'm putting in 2 new bathrooms which will be stacked. Each bathroom will have a tub/shower unit, toilet and sink. I plan on running a 3" stack that will connect into clay sewer drain in crawl space and run all the way up to attic space. Each toilet will connect into this 3" stack with 3" pipe as well.
Is it ok if I connect the shower/tub with 2" pipe to the toilet run and then connect the sink with 1 1/2" pipe to the shower/tub run?
Can I connect the sink directly to the toilet run and the shower/tub directly to the toilet run instead if I like?
Can tee's be used on both horizontal and vertical drain lines as long as they are not on their back?
Wye's can be used on both drain and vent lines in any position correct?
I plan on running a separate vent (1 1/2" pipe) from both the 1st floor sink and shower/tub unit up to the 2nd floor and teeing in the 2nd floor shower/tub and sink (above flood rim) and continuing the 2 vents into attic space and connecting to main stack, is this called "dry venting" and is it ok?
Finally, would a 2" vent through the roof be sufficient or would I need to go to 3"?
NOPE...sorry, adding washing machine anywhere on the toilet drain line is a No-NO when it comes to WET VENTING...OK?
You would be better to cut a 3"x2" wye into the vertical stack above the toilet sanitary TY fitting and then running pipe over to where it needs to go...again hanging every 4 feet with 1/4" pitch per foot of piping. You would also install a 2" cleanout like you have installed at the 4" drain line and then reduce the tankless heater drain line to 1.5"....add P-TRAP, and I am afraid, an individual 1.5" vent is needed, too.
You may also be required to add a TRAP PRIMER to this installation...depending on how often condensation/discharge from the tankless heater occurs.............BUT, as I always seem to say to people.........You need to check with your plumbing inspector to see if you need to do this...ok??
A trap primer is simple device that spills about a tablespoon of water into the p-trap every time a fixture it is hooked to is operated (usually hooked to a sink water line and then copper pipe is usually run over to the trap (pipe must pitch for water to fall via gravity to p-trap). This will prevent the p-trap from ever drying out and allowing sewer gas to flood the house/basement, etc.
Never easy huh Steve...
Check into the trap primer....let us know if need more.
Geez.. Is that I all I have to do Would I be allowed to run a 3/4" pvc drain line (like used in HVAC) from the closet to a floor drain in basement?
Also, I am having a air handler installed in our attic for our 2nd floor heating/AC, I was told by the HVAC company that I could run a 3/4" PVC drain line through attic, down 2nd floor and 1st floor walls (closet space) and drain into floor drain in basement, would this be allowed?
Quote:
Originally Posted by massplumber2008
Hi Steve:
NOPE...sorry, adding washing machine anywhere on the toilet drain line is a No-NO when it comes to WET VENTING...OK?
You would be better to cut a 3"x2" wye into the vertical stack above the toilet sanitary TY fitting and then running pipe over to where it needs to go...again hanging every 4 feet with 1/4" pitch per foot of piping. You would also install a 2" cleanout like you have installed at the 4" drain line and then reduce the tankless heater drain line to 1.5"....add P-TRAP, and I am afraid, an individual 1.5" vent is needed, too.
You may also be required to add a TRAP PRIMER to this installation...depending on how often condensation/discharge from the tankless heater occurs.............BUT, as I always seem to say to people.........You need to check with your plumbing inspector to see if you need to do this...ok??
A trap primer is simple device that spills about a tablespoon of water into the p-trap every time a fixture it is hooked to is operated (usually hooked to a sink water line and then copper pipe is usually run over to the trap (pipe must pitch for water to fall via gravity to p-trap). This will prevent the p-trap from ever drying out and allowing sewer gas to flood the house/basement, etc.
Never easy huh Steve...
Check into the trap primer....let us know if need more.
Uh oh... Ran into an issue today It appears the path I originally choose to run the vent from the 1st floor sink is not gonna work (I'd have to cutout 2 1/2" of a 4" header in a loading bearing wall). I should have realized this at first, but I didn't.
Are you allowed to run the vent for the 1st floor bathroom group from a connection under the floor such as via a WYE on horizontal run of the sink drain line?
If no connection under the floor is allowed, is there a limit on the # of 90's that can be used on the vent lines?
Also, do I have to use a long sweep 90 when connecting to toilet flange or a regular 90 is fine?
Are there requirements by code as far a distances you have to stub out the drain and supply lines from walls or floors? Or toilet supply stubout?
Is there a required # shut off valves needed (not talking about the chrome ones under sinks or toilet tanks)?
I was only putting a shutoff valve before/after meter and on tankless water heater. My house I live in now has shutoff's in the basement everywhere (most leak too), they have ones to shutoff the water to the 2nd floor, ones to shutoff the water right before shower faucet. etc..
And lastly, I understand you have to support horizontal lines every 4 feet, but are vertical lines required to have any clamps or supports?
Thank you all once again, hopefully I'll get this right soon!
P.S. Inspector says I'm allowed to use AAV on laundry standpipe and vent pipe must extend out roof 12" (minimum) to 16" from lowest side of roof which you are going through.
No problem at all Mark, I appreciate the help. I have a remote control helicopter, sure wish I could keep it in the air for more than 2 minutes without crashing
Quote:
Originally Posted by massplumber2008
Steve..I'm off to fly remote control airplanes with my kid...I'll be back around 9:00 or so. Check back then for my reply..ok??
Always amazes me to see a little person fly anything (kites, airplanes, helicopters...even paper airplanes)..even if only for a minute or two. We actually flew kites this weekend over 100 feet in the air...good times!!
Lucky you that you get to use an AAV at the standpipe!! Just be sure it is readily accessible...as per code requirement!
And sorry...NO...there is no way to run a WET VENT system from under the floor. In fact, except for an island sink installation there are no vents that are allowed to run up to fixture and then back down under floor to then run a distance and then run up the wall and connect into a vent 6 inches above flood level rim....so again, simply cannot run vent for entire bathroom from under the bathroom...
May be a good idea to ask inspector to drop by for a minute if he has to inspect all this anyway. If nice guy, maybe he'll pop out for fun. If super busy guy, may charge an inspection fee and then require a "reinspection fee"...but if it saves you time and labor, may be worth investigating this (reinspection fees in my area are $25.00 to $50.00)..doesn't hurt to call!!
Now, there is not a LIMITED number of elbows as much as there is a LIMITED DISTANCE that a vent can run. If I remember correctly, total horizontal distance cannot exceed 1/3 overall length of total developed distance (length) of vent...here a vent with a total developed length of 30 feet should only have a 10 foot horizontal section of piping to vent. AT least that is how my code book calls it...
Check with your inspector to see if he agrees.
Toilets can connect to toilet flange via regular 90 or even a street 90 if necessary.
STUBOUTs:
Toilet water is usually six inches left of center of toilet flange and 6" to 8" high off finish floor.
Toilet drain at 11.5" to 12" to center off finish wall.
Lavatory drain is usually 17-18" off finish floor.
Lavatory water is usually 20" off finish floor.
Check specification sheets of planned fixtures to be more specific...ok??
Shutoffs:
At each individual fixture as you know...then I would isolate the bathroom itself if possible (costs $30.00 now for 2 shutoffs)..if not, not required as you presented your house layout!
Finally, you should plan on supporting/strapping vertical pipes at each floor level...mostly common sense here. Don't span entire floor without some vertical support at mid pipe somehow (straps or clips work great).
I just wanted to thank you once again for your help and for answering my many, many questions. Hopefully I have all the information I need to finish this correctly so I can move on to the next phase. Maybe when I'm done I'll take some pictures and post them after inspection. Now if I could just get my solder joints to look good
How are you? I started the copper rough in today and I was wondering, do they sell compression type straight and angle shut offs for 3/4" copper or do you always have to reduce down to 1/2" at stub out for the toilet and sinks?
Also, should I reduce down to 1/2" right before connecting to shower/tub faucet or keep it at 3/4" the whole !way?
Is there a certain distance you have to keep the copper spaced when running to the faucet? Like 8" center to center, etc?
I'm great...how are you? How did you finally work out your vent issue??
Reduce the 3/4" to 1/2" at the sink and toilet....then purchase normal straight and angle compression shutoffs as needed (see pic. below....ordered as a 5/8" OD compression by 3/8" OD compression ANGLE or STRAIGHT stop). You'll also want to pick up some 1/2" copper tubing size or 5/8" OD copper tubing size flanges to cover the holes.
After installing the shutoffs you will need to hold against yourself and tighten the packing nut as in my 3rd picture below. Just 'til nut feels snug..ok?? These leak alot AFTER installation...so give a little TWEAK to the packing nut and you should be all set.
The tub/shower valve...if it has 3/4" inlets then feed it full size 3/4" copper tubing. Here, more volume is never a bad thing. If inlets to valve are 1/2" reduce anywhere along the line and will be fine, too!!
In terms of center to center....no absolutes here unless pipes are going to be exposed then there are standards to adhere too.
For bathroom sinks I usually pipe water at 20" off finish floor, at 6 or 8" centers...
For toilets, water is generally 6" over from center of toilet flange and 6-8" off finish floor.
Flexible connectors will then allow FLEXIBILITY in connecting shutoffs to sink and toilet.
Always best to check the ROUGH in sheet for the toilets though as some toilets nowadays want water roughed as high as 10" off finish floor...so double check your installation instructions..ok??
Hope that answered your questions...let me know when/if have more...
Would I be allowed to run a 3/4" pvc drain line (like used in HVAC) from the closet to a floor drain in basement?
It appears the path I originally choose to run the vent from the 1st floor sink is not gonna work (I'd have to cutout 2 1/2" of a 4" header in a loading bearing wall). I should have realized this at first, but I didn't.
Linear Mode
