Ask Experts Questions for FREE Help !
Ask
    darlaphilipczyk's Avatar
    darlaphilipczyk Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 20, 2007, 01:44 PM
    Replacing J pipe under kitchen sink
    The old J pipe basically disintegrated in my hand when I pressed my thumb against the leak. So I bought a new one, matching it exactly to the metal one I removed. I asked them at Lowe's about joint compound and they said use plumber's putty. Here is my question: How does one use plumber's putty? This may sound silly but I have never done any plumbing repairs and while the J pipe fits snugly, I don't want it to leak again. Please instruct me and thank you for your time.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #2

    Oct 20, 2007, 02:59 PM
    This is why big box salesmen aren't out there doing plumbing. YOU DON'T USE PUTTY on a compression joint. You use the washers that came with the "J" bend. Place the compression nut and washer on the tail piece coming out of the sink and the other washer on the piece coming out of the wall. Make sure that the washer goes UNDER the lip. Start the nuts being careful not to cross thread. Now take a pair of large pliers and tighten the nuts until they are snug. Stop off a tub and run a few inches into it. Let the water drain out and check the trap for leaks. If you see any leak arounds the nut snug them up a little more. Good luck, Tom
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #3

    Oct 20, 2007, 08:07 PM
    The Home Depot guy said "We're not a hard ware store".

    Me, I go the extra mile and use some silicone grease (In plumber's Asile) on the threads and the compression washer. Aids in removal and helps the seal.

    Drain cleaner and just plain time loves to eat through these metal pipes.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #4

    Oct 21, 2007, 10:37 AM
    You DO NOT use putty, grease, or silicon jel on compression nut threads. Since the threads don't hold anything but the compression washer it's useless to load them up with anything and if the joints line up on the compression fittings you don't need to add anything there either. Sorry, Keep it simple. Tom
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #5

    Oct 21, 2007, 03:20 PM
    Tom:

    Good vacuum practice and automobile practice and refrigeration practice says to grease the "O" rings with a compatible fluid/grease. Why does plumbing have to be different? I know the rubber washer is flat, but the principle applies. As you tighten a non lubercated fitting, there is a tendency for the washer to get distorted. Grease prevents that process.

    The silicon grease on the threads assures easy removal at a later time.

    Not required. Just helpful
    Try this test:Take a trap and grease the threads. Take another trap and don't grease the threads. Wait 20 years. Which trap will be easier to remove?

    Silicon grease does no harm. In fact, it makes the next plumber's job potentially easier.

    Note here prevents the rubber from drying out:

    Silicone Grease and Compounds

    and this one:

    Select Products Plumbers Grease

    which states:

    Plumbers Grease Lubricates & Protects metal, rubber & Plastic parts. (Use on "O" rings & value stems)

    Note the word metal which the P trap is made of.

    Sorry Tom, I still disagree. Hopefully I've provided proof that it's a "GOOD IDEA".

    If easy removal is a good thing.
    If lubercation makes easy removal.
    If silicon grease is a good lubercant.
    If silicon grease is compatible with water systems.
    If silicon grease prevents rubber/"O" rings/gaskets from drying out.
    If a metal P trap contains a rubber gasket.
    If a metal P trap is made of metal

    Then silicon grease can be used on metal "P" traps to prevent gaskets from drying out and also the facilitate removal of the fittings at a later date.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #6

    Oct 22, 2007, 05:50 AM
    KeepitSimple,
    You make a valid point. Although I've never used used lubricants on compression fittings and still advise against putting any kind of lubricant on plastic threads you have a point well taken. Thank you for correcting me. Tom
    jimbeau38's Avatar
    jimbeau38 Posts: 1, Reputation: 1
    New Member
     
    #7

    Jul 27, 2010, 07:29 AM

    I used Keepitsimplestupid's advice and it put an end to many hours of hassling over my kitchen sink problem. The rubber tail piece gasket kept twisting as I tightened the nut and a little grease is all I needed to end the problem. I tried silicon caulk on the outside, but that didn't work and the more you tighten the worst the leak got. A little bit of grease worked wonders. Thanks Keepitsimplestupid!! The whole internet and no one else mentioned this... That is plain stupid.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Fog horn noise when using taps in bathroom sink and kitchen sink [ 1 Answers ]

There has developed, in the last week, a "fog horn" sound when we turn on the hot or cold taps in the bathroom or kitchen. It does not occur when we use the washer or dishwasher. Could anyone give some advise on what could be the cause of this?

Kitchen sink drain pipe leak [ 1 Answers ]

I have a big leak under the kitchen floor, I went under the house and I can see the leak which is right in the center of the kitchen. The crawling space was very minimal and hard to get to the cast iron pipe. I was thinking about opening the kitchen floor which is wood to see if I can fix the...

Replacing J pipe under bathroom sink [ 1 Answers ]

Can I get some instructions on how to do this properly? It had started to leak at the connection under the sink, and when I went to inspect it it just came apart! I have the parts to replace it. I don't want to call a plumber just for this. It seems like it should be simple but of course is not...

Pipe snapped replacing bathroom sink [ 3 Answers ]

My cold water pipe snapped behind the shut off valve on the threads inside the wall. I do not know how to weld properly and the main water supply for the whole house is shut off. What do I do? Is it possible to bypass just one bathroom sink and allow water through out the rest of the house?

Leaky pipe under kitchen sink [ 2 Answers ]

Hi, I just moved into my new house and I have a problem with the kitchen sink. When water is just running through the sink and pipes, there is no leaking. However, when I fill up the sink with water (say to soak pots) and then let the water out, the pipes underneath leak terribly as though the...


View more questions Search