 | | | PVC joint under bathtub is leaking
Asked Nov 6, 2006, 07:35 AM
—
5 Answers Hi,
I just found that when the water was coming out of overflow drain of the bathtub, the PVC joint under bathtub was leaking. Is there any eay way to seal the joint without replace the PVC joint?
Thanks
Sheng Thread Summary |
5 Answers
 | Uber Member | |
Nov 7, 2006, 03:02 AM
| | | Not realistically. I've seen people make the attempt with silicone...but you just end up with a mess.
If you can get to the fitting from an access panel, check it out. You probably don't need to replace the fitting. It may just be loose, or may need a washer or washers replaced. | | |  | New Member | |
Nov 7, 2006, 07:27 AM
| | | I am able to access that joint. I will try to check the washer first. Thanks! | | |  | Senior Plumbing Expert | |
Nov 7, 2006, 09:04 AM
| | |
"I just found that when the water was coming out of overflow drain of the bathtub"
Those words concern me more then the leak at the trap raiser. You have a blockage downstream from the bathtub. The solution would be to snake the drain line from the lavatory roof vent. Once you remove the standing water in the trap the leak will be greatly diminished to the point of just snugging up the compression nut. Rergards, Tom | | |  | Über Member | |
Nov 7, 2006, 09:25 AM
| | | Yeah, snake it like Tom said.
If the joint is a compression or other threaded joint, tightening the nut may work as already suggested. If not, opening it and replacing the gasket may not be too bad of a job.
Leaks in a cemented PVC joint are rare. One of the reasons I like using it. It is so easy, I can't mess up. I have managed to stop a small leak somebody else left me in a PVC drain. I got it clean and dry and smeared the regular joint cement on it. Took a couple of coats, but did the trick. I am not sure I would want to install new drywall under such a fix.
Even if you have to repair a PVC to PVC, it won't be too bad. Just cut the bad section out and couple a new one in. | | |  | Junior Member | |
Nov 7, 2006, 01:20 PM
| | | Would something like Power Wrap (sp) work for a leaking PVC joint? | | | | Thread Tools | Search this Thread | | | | Add your answer here.
Check out some similar questions!
Broken bathtub drain - PVC near slab [ 2 Answers ]
During the course of replacing a bathtub, the drain pipe got caugt on the tub and it broke the PCV joint near the slab. The coupling broke, but the PCV piece that comes in through the slab fully intact. However, it is still glued into half of the coupling. There does not appear to be enough room...
Need help with water carrying pvc joint [ 5 Answers ]
Pvc pipe joint between floors has become unsealed so that it leaks minutely. So far anyway. Is there a product that will reseal this joint. Otherwise I will have to cut a large hole in the ceiling to remove and replace the old joint. It is a straight connection not an elbow if that makes any...
Bathtub drain leaking [ 1 Answers ]
Hi! I sure could use some help ! My Mom's bathtub is leaking around the outside of the drain. When water drains out after a shower or a bath it goes down the drain and comes up on the outside of the drain under the tub then it seeps out on the bathroom floor. We thought it was maybe the shower...
Leaking Bathtub. [ 1 Answers ]
I bought a condo a few months ago, and my neighbor (who lives under us) says that sometimes there is a leaking through their bathroom ceiling. The strange thing is, it does not leak (or at least she doesn't notice it) when we take showers, only when we take a bath. I do have an access panel behind...
Leaking bathtub [ 1 Answers ]
Hello help desk,
Over the past few weeks we have experienced dampness on the carpet leading toward the bathroom. I noticed this after children would take a bath.
Orginally, I thought it was caused from spalshing etc.. However lately I noticed that when we let the water out to drain, ...
View more Plumbing questions Search |
|