Ask Experts Questions for FREE Help !
Ask

New vanity will not touch wall due to water valves

Asked Jan 3, 2012, 09:55 PM — 3 Answers
Bought 2 new Antibes but the drawers hit my high water valves. How can I fix this? I am not a plumber but can't afford to pay anyone at this moment

Search this Thread
Share |
3 Answers
creahands's Avatar
creahands Posts: 2,507, Reputation: 884
Ultra Member
  
#2

Jan 4, 2012, 04:04 AM
Cut the draws to clear the valves. Depending on way drawers were built will determine if u cut the back.

If drawer were built as a box with fronts added on it would be easier to make cut at front.

Remove front and make cut. Put back together with glue and small nails.

Good luck

Chuck
Helpful  (1)
speedball1's Avatar
speedball1 Posts: 27,655, Reputation: 9541
Senior Plumbing Expert
  
#3

Jan 4, 2012, 05:29 AM


Hi Terold and welcome to the Plumbing Page.
Chuck gave you one option.
Another would be ton open up the wall and lower the angle stops and supplies. You could leave the wall open as the vanity would cover it. I know this would involve bringing in a plumber but that's what I would do if I didn't want to cut up my vanity. Good luck in whatever you decide. Tom
Helpful  (1)
Milo Dolezal's Avatar
Milo Dolezal Posts: 5,879, Reputation: 1933
Plumbing Expert
  
#4

Jan 4, 2012, 07:26 AM


From my experience, drawers usually end about 2 1/2" from the wall. That's enough to absorb angle stops. See if you can move the valves closer to the wall w/o cutting cabinetry or the wall. Back to you. Milo
Helpful  (1)
Not your question? Ask your question View similar questions
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

Water is leaking under or behind vanity, but not in vanity.Only when water is running [ 2 Answers ]

I have noticed for the last week or so my toilet has been clogged off and on. I would plunge it, and it would be fine for a few days, then it would clog again. This evening I was shaving my face and I noticed a puddle forming either under or behind the vanity. I quickly shut the water off. I...

Touch 'N Go Garage Door - Wall mounted touch pad [ 3 Answers ]

The (garage) wall-mounted touch pad for my Touch 'N Go Garage Door opener (Model 1000A) no longer works. I realize that this product is no longer in production, but are there any outlets where a replacement pad can be ordered OR will any universal wall-mount pad work for this unit?

How do I fill in the space between a vanity and a wall [ 1 Answers ]

I have three inched of space between my vanity and the wall - how can I close up that space to match the vanity

My corner tub and vanity are pulling from the wall [ 3 Answers ]

I noticed that my tub and vanity which are on the same outside wall attached to each other are pulling away from the wall, with about a 1/4 inch space or more on the vanity and a 1/8 inch or so gap downward from the recently redone caulk on the tub. The house is about 14 years old. Never used...

Vanity water supply valves leak [ 2 Answers ]

In replacing the hot and cold water supply valves under the sink I have a slow leak. The end of the copper pipe has a ridge on it with a nut receptacle behind it where I am screwing the new valve into. I have used tape and grease with no luck. Any suggestions?

View more Plumbing questions Search