Ask Experts Questions for FREE Help !
Ask

    Moving a Toilet 90 Degrees

    Asked Oct 6, 2005, 02:42 AM 3 Answers
    The question I'm about to ask is very similer to others for verticle waste not horizontal and the answers don't seem to fit what I have so apologies if I'm repeating something?

    My toilet backs on to an outside wall and connects to the 4 inch upvc waste with a standard straight connector goes through the wall then 90 then short sloping run to the main stack all very simple so far. I want to turn the toilet 90 degrees which will then back onto a internal solid wall. I thought I could use a standard wc 90 elbow back to the exsisting join but the problem is the toilet with the elbow will be to far in to the corner and if I pull the wc forward there will be a gap between the wc and the internal wall. It's a p type trap close coupled toilet.

    When other work in the bathroom is completed I wish to change to a back to wall type with new units behind, if these are not deep enough I will have the same problem with the new wc.
    I suppose an easy fix would be to move the inlet through the wall back a bit but that's seems like a lot of work just for a few inchs or can I use 45,90 elbows or flexi pipe to do this. I suppose the shape will be like a ? Looking down on it.
    Can I also connect my sink waste to this as I have seen an elbow in b&q with a 32mm inlet on the bend as the sink is going next to the wc on the internal wall? Thanks for any help in advance.

    Last edited by grumanpi; Oct 6, 2005 at 03:13 AM.
    Search this Thread
    Share |
    3 Answers
    speedball1's Avatar
    speedball1 Posts: 28,590, Reputation: 1910
    Senior Plumbing Expert
     
    #2

    Oct 6, 2005, 04:01 AM


    You wish to install a dog leg to bring the toilet closer to the wall? Why not use a 90 and fur the wall out?
    Also you may connect the 1 1/4" drain from the lavatory providing the lavatory's vented. Good luck, Tom
    Helpful
    grumanpi's Avatar
    grumanpi Posts: 3, Reputation: 1
    New Member
     
    #3

    Oct 29, 2005, 01:42 AM
    Thanks for the help I ended up moving the waste along the wall a few inches and used an elbow with a 32mm take off for the sink works great. Only down side was making another hole in the wall and refinishing inside and finding some bricks to match a 50 year old house on the outside, got a close match from local building yard this was more work then the actual plumbing so now all is finished and the wife's happy ha ha.
    Helpful
    speedball1's Avatar
    speedball1 Posts: 28,590, Reputation: 1910
    Senior Plumbing Expert
     
    #4

    Oct 29, 2005, 06:18 AM


    Congratulations on a job well done. Tom
    Helpful

Not your question? Ask your question View similar questions

 

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.


Check out some similar questions!

Rotating Toilet 90 degrees on Cast Iron Flange [ 1 Answers ]

I am remodeling a bathroom in a 60s vintage home with adequated crawl space. I need to rotate the toilet flange 90 degrees to install the new toilet as the orientation has changed with the remodel. The materials of construction for plumbing is cast iron. I am keeping the same elevation of floor....

Moving a toilet [ 4 Answers ]

I am remodeling the bathroom in my apartment and would like to move the toilet about 6-8 feet from where it is now. I live on the fourth floor of a co-op building with cement slab floors and drilling into them is not an option. I am planning on building a platform for the entire bathroom floor to...

Moving a toilet... [ 35 Answers ]

Hello - I am in the process of a major bathroom remodel. The bathroom is almost exactly 10X10 and I am swapping the shower and toilet locations (they are currently in opposite corners of the room). Draining/Venting the shower will not be an issue as I can tap into the same 2 inch drain pipe. The...

Moving a toilet! [ 1 Answers ]

Hi, I am going to start a project and I will be moving a toilet about 10' to the left. Right now the toilet drian line is a 4" cast iron one. The questions I have are: 1. What do I use to connect the new line to the old cast iron one? -I am hoping to use a ABS line for the new toilet...

Moving a toilet in the Basement [ 4 Answers ]

I want to move my basement toilet to another location as part of a bathroom remodeling project. I have a cement floor. The toilet sits on top of a 2.5 inch build up of cement... kind of like a platform of some sort. The vent pipe appears to go into the cement and I assume connects to the toilet...


View more questions Search