Kitchen faucet water will not turn off!

http://www.askmehelpdesk.com/plumbin...et-173396.html

Iversonlady32,
Frist , there is probably a valve under the sink by which you can turn off the hot water to the sink faucet. You then can turn on the main water valve, so that you have water to the house.

Now, what type of kitchen sink faucet do you have, single lever or two knobs? Brand if you know.

Fredonia2k,

I don't understand your post. Your link takes me to Misscoops post, are you responding to Iversonlady's post, Miss coops post, or are you posting your own post.

Hey! Thanks for the quick response and the idea to shut off just that valve... SO HELPFUL! Unfortunately, I do not know the brand, or model of the sink, very old has been here since we moved years ago! :-) It is a two knob faucet.

OK.
Remove the screw holding the knob on. If you do not see a screw it is covered by a small cap in the center of the knob. Remove the cap with a sharp pointed tool, then remove the knob screw. If you have difficult removing the knob pry under one side then the other of the knob with a screwdriver. If its really stuck you may have to purchase a handle puller, shown below. After removing the knob, the next thing you see is the bonnet nut. That's the nut around the stem that the handle was on and holds the stem in. After removing the bonnet nut, put the knob back on the stem and unscrew the stem, just like you are turning the water on. After the stem stops rising up pull it out with a pair of pliers.

If you faucet is as old as you indicate it will be the compression washer type. Replace the washer on the end of th stem. These washers come in standard sizes, just take the washer to the store with you to get the correct size. If you have a newer type faucet you will have a cartridge type stem. Take it to the store for replacement. If the local Home Depot or Lowe's can't match it go to a plumbing supply. The people there are more likely to recognize it.

If you have the older type compression washer type you will probably need to replace the seat. The seat is the part that the washer presses against to shut off the water. For that you will need a seat wrench, also shown below. You put the wrench in the hole where the stem was and feel for it sliping into place in the seat. There are two ends on the seat wrench, one is several sizes of square the other end is hex shaped . If one doesn't work try the other. After removing the seat take it to HD, Lowe's, hardware store or plumbing supply for replacement. There is a thousand and one different sizes, shapes, and threads of seats. To put the seat back in you put it on the end of the seat wrench, put it back down the stem hole and screw it back in. The put the stem back in. After you have started the bonnet nut turn the stem to the open position, then tighten the bonnet nut. If the stem is in the closed position you won't be able to screw the bonnet nut all the way in. Tighten the bonnet nut until the stem feels a little tight as you turn it. If water leaks around the stem after you turn it back on, tighten the bonnet nut, a little at the time until leak stops.

Thank you so much I will try that... Question... Would it be easier to just replace the faucet. I mean the faucet is super old! Lol

Not much more work, just the cost of the faucet. Sorry, forgot to post pics.

Attached Images

  

I would like to add my two penis also, is it possible to post a picture of your faucet, and
I would suggest to replace the faucet as Harold says it is not hard but the price, good luck.

John

John...you keep your two penis' to yourself...

Penis...pence...pennies...cents...? Which one....I'm not sure here? You also talked of PP over at the price pfister faucet issue...hmmm...?

May want to edit your post there john... I will edit mine later!

Have good day all...

MARK

Mark thanks for letting me know, I am sorry guys, I was typing to fast, I meant pennies I appolagize for the miss spell and to let you know I don't have two, Thanks.

Best Regards,
John