Ask Experts Questions for FREE Help !
Ask
    435Studio's Avatar
    435Studio Posts: 93, Reputation: 4
    Junior Member
     
    #1

    Jul 23, 2009, 05:17 AM
    Drywall around Electrical Panel
    When installing drywall around the main electrical panel should I take off the panel cover and then reinstall the cover after the drywall is in place? Is switching off the main breaker all I need to do as a precaution?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
     
    #2

    Jul 23, 2009, 05:24 AM

    If the cover is a flange type, in other words extended to cover the wall finish, then you would need to remove the cover.

    Shutting of the Main Breaker is definitely required.

    If the Main breaker is in that panel, there will still be live conductors that feed the Main Breaker and extreme caution will be needed.
    435Studio's Avatar
    435Studio Posts: 93, Reputation: 4
    Junior Member
     
    #3

    Jul 23, 2009, 05:39 AM

    Follup- is there somewhere else to disconnect the power, outside, maybe?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #4

    Jul 23, 2009, 08:21 AM

    Maybe, depends on what you have. Many homes just have a meter showing, no box to open. Post a picture and we could tell better. Like TK said the open panel will still have power but just don't stick fingers or screw drivers in there.
    435Studio's Avatar
    435Studio Posts: 93, Reputation: 4
    Junior Member
     
    #5

    Jul 23, 2009, 11:24 AM

    No worries, I don't plan on "poking around" inside the panel while the cover is off. I just wanted to make sure I wasn't missing something. Thanks for the quick answers!!
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #6

    Jul 23, 2009, 11:42 AM

    As an Electrician, I leave the cover off, and cut a piece of cardboard same size as inside of panel, push inside the outer lip, and maybe a couple pieces of fir strips sideways to hold in
    Place. Protects the breakers, and painter won't get paint on the buss.
    It is easier to keep clean than it is to clean it.
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
     
    #7

    Jul 24, 2009, 07:52 PM

    I assume that you are framing and drywall around a surface mounted circuit breaker panel. I suggest that you frame around it, leaving about 6" on each side and the top and bottom. Then build a cover for that opening. You might want to get into that panel to do some wiring one day.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #8

    Jul 25, 2009, 05:53 AM

    I was thinking this was inwall, if so, stub spare conduits out of top and bottom.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Electrical Sub-panel [ 1 Answers ]

Running electrical sub panel to pole barn.Does this require 3 conductor service entrance wire with ground ( 2-2-2-4 ser)? Or 2-2-2 seu ?

Electrical panel [ 2 Answers ]

Can I convert an old square d qo panel from a main lug panel to a main switch without doing a service change?

Electrical panel 400 amp [ 2 Answers ]

Oh I am shopping in Miami, Florida or Fort Lauderdale Florida

Electrical Panel Box [ 1 Answers ]

I know I ask this before but what is the minimal height then for a electrical panel box, I was given the maximum, please let me know the minimal, thank you!

Electrical Panel [ 1 Answers ]

How many watts can go on a circuit that is 2 x 20 = 40 amps?


View more questions Search