Ask Experts Questions for FREE Help !
Ask
    Karl Haughton's Avatar
    Karl Haughton Posts: 1, Reputation: 1
    New Member
     
    #1

    Dec 2, 2006, 04:54 AM
    How to insulate a cathedral ceiling in a house
    Please tell me how to insulate a catherdral ceiling
    TorontoCarpenter's Avatar
    TorontoCarpenter Posts: 5, Reputation: 1
    New Member
     
    #2

    Dec 2, 2006, 07:56 AM
    Quote Originally Posted by Karl Haughton
    Please tell me how to insulate a catherdral ceiling
    Three rules to this answer.

    1. air movement between the roof sheeting and roof framing members and the insulation at least 1 1/2 inches of air space for the air to circulate from the soffit ( the inlet ) to the ridge vent ( the outlet)
    skiberger's Avatar
    skiberger Posts: 562, Reputation: 41
    Senior Member
     
    #3

    Dec 2, 2006, 07:58 AM
    First you need to install rafter vents. These are styrofoam vent section that you will staple to the under side of the roof sheathing from the eave area to the ridge. These are in the insulation area of the home centers.
    These vents will allow an air gap so air can flow from the eave vents to the ridge vent.

    Then install the insulation with the paper side toward the living space. R19 to R25 is the standard insulation you'll be able to fit between a 2x6 & 2x8. If your rafters are 2x10 you can increase the insulation to a R30.
    TorontoCarpenter's Avatar
    TorontoCarpenter Posts: 5, Reputation: 1
    New Member
     
    #4

    Dec 2, 2006, 08:05 AM
    R-21 is the minimum which is 5 1/2 inches, R-38 is the max 12 inches. And last thing which is very important 9mm poly, and tape the seems with tyvek tape. Keeps moist warm air from getting into the insulation which will breed mold in that area.
    sandieft's Avatar
    sandieft Posts: 1, Reputation: 1
    New Member
     
    #5

    Nov 18, 2007, 02:42 PM
    Quote Originally Posted by Karl Haughton
    Please tell me how to insulate a catherdral ceiling
    What do I do if I don't have a ridge vent because my cathedral ceiling butts up to the wall?
    TorontoCarpenter's Avatar
    TorontoCarpenter Posts: 5, Reputation: 1
    New Member
     
    #6

    Nov 18, 2007, 03:01 PM
    Quote Originally Posted by sandieft
    What do I do if I don't have a ridge vent because my cathedral ceiling butts up to the wall?
    Not to worry, you can still vent out the sides mind you it still has to be close to the top of the roof where the wall and roof meet. You should cross vent the roof out the sides or one side either the left or right side. It's not as good as a ridge vent but it'll do the job just fine. Just remember to measure back off the wall 24 inches or so along the roof slop to install your vent to avoid the wall flashing and vent flashing from over lapping... good luck !
    TerryB's Avatar
    TerryB Posts: 53, Reputation: 3
    Junior Member
     
    #7

    Nov 21, 2007, 10:04 PM
    Or, a false wall to continue the ventalation up to the next roof.
    astrobiker's Avatar
    astrobiker Posts: 2, Reputation: 4
    New Member
     
    #8

    Feb 23, 2008, 07:18 AM
    There is a considerable amount of misinformation on the web about insulation of cathedral ceilings. There is a science to this that must be followed. There is no single, simple answer to this question because it depends on the climate zone you live in.

    First, for the most complete answer, go to buildingscience.com and search. They give a full treatise on this topic.

    The abbreviated answer is that the underside of the roof sheathing needs to be protected from moisture and condensation. However, many of the commonly accepted practices only answer part of the question or lead to unsatisfactory, partial solutions.

    If you are venting under the sheathing
    :
    The purpose of venting is to allow a clear air flow to every cavity. In order for this to occur, you need: a) a clear passageway under the sheathing, preferably 2". 1" is too small even though it is often recommended; b) sufficient venting at soffit and ridge. Sufficient is defined as the area of the room below divided by 150 to 300 depending on the conditions. Safest is to shoot for 150. That is: room area / 150 equals square feet of venting.
    So, for example, if you have a 500 square foot room, then you need approximately 3 square feet of venting area at the soffit and the roof. Many soffit and ridge vent systems are inadequate in this regard, providing vastly less area than this. See Cor-a-vent's website for details of venting. They have excellent documents describing proper venting.
    Note that this precludes the "side venting" suggested by another poster unless you can figure out how to get 3 square feet of venting out the sides. Most people use those little 3" vent plugs that might have a square inch of air space, if you're lucky.

    Note that this is NOT the case of "I can't do it completely, I'll do it partially". If you don't have enough area, then the air flow will be inadequate.
    Also, another problem is that most cathedral ceilings have skylights. These are blocked areas that cannot be vented without cleverness.

    If you are NOT venting under sheathing

    Contrary to popular opinion, venting is not necessary, and can do more harm than good if not implemented properly. Remember, the key is to keep the roof sheathing from getting wet. Most moisture is carried by air movement. For example, a recessed light installed in a cathedral ceiling is roof rot ready made.
    The best solution is to apply closed cell polyurethane spray foam directly to the underside of the roof sheathing. 2-3" is necessary in most climates, but see the Building Science literature for details. Closed cell polyurethane is a very effective vapor retarder when applied to these thicknesses. If moisture cannot reach the roof deck, you're in good shape (as long as the roofing above it is in good shape).
    The advantage to this solution, as noted, is that internal warm humid air can't even touch the sheathing, so it will never condense. This air seals and insulated. So, if you install recessed lights in the sheetrock below, you're still protected. Every other solution fails when you have ceiling penetrations, especially if you place a vapor barrier like plastic sheeting in the ceiling. Since the vast majority of moisture movement is at penetrations. If you install plastic sheeting, the electrician will cut a big hole in it where the recessed light pokes through. Since all such fixtures leak, unless extremely carefully detailed (never done), the air will leak into the cavity. With normal insulation (fiberglass), this moisture then gets trapped in the cavity by the plastic, rotting out your roof unless you have ample air flow to carry the moisture away.

    Another solution is to use dense packed cellulose. This is defined as ~3.5 pounds per cubic foot. Studies on thousands of homes (see Applegate insulation's website) have shown that fully filling the cathedral ceiling cavity minimizes air infiltration and provides a long lasting roof with good insulation. The key is that it has to be dense packed cellulose and there must be no venting into this space.

    This just touches on a couple key considerations. To summarize:
    If you're going to ventilate, you have to do it right
    If you use fiberglass, you have to ventilate
    If you use spray foam, you should not ventilate, nor should you use any other vapor barrier.
    If you use dense packed cellulose, do not ventilate or use vapor barriers.
    Dave in SV's Avatar
    Dave in SV Posts: 1, Reputation: 1
    New Member
     
    #9

    Dec 19, 2008, 11:23 AM
    I want to insulate the roofline of my pole barn (steel roof). Any suggestions on how to do that? I am thionking of following the top chord of the trusses.
    Quote Originally Posted by astrobiker View Post
    There is a considerable amount of misinformation on the web about insulation of cathedral ceilings. There is a science to this that must be followed. There is no single, simple answer to this question because it depends on the climate zone you live in.

    First, for the most complete answer, go to buildingscience.com and search. They give a full treatise on this topic.

    The abbreviated answer is that the underside of the roof sheathing needs to be protected from moisture and condensation. However, many of the commonly accepted practices only answer part of the question or lead to unsatisfactory, partial solutions.

    If you are venting under the sheathing
    :
    The purpose of venting is to allow a clear air flow to every cavity. In order for this to occur, you need: a) a clear passageway under the sheathing, preferably 2". 1" is too small even though it is often recommended; b) sufficient venting at soffit and ridge. Sufficient is defined as the area of the room below divided by 150 to 300 depending on the conditions. Safest is to shoot for 150. That is: room area / 150 equals square feet of venting.
    So, for example, if you have a 500 square foot room, then you need approximately 3 square feet of venting area at the soffit and the roof. Many soffit and ridge vent systems are inadequate in this regard, providing vastly less area than this. See Cor-a-vent's website for details of venting. They have excellent documents describing proper venting.
    Note that this precludes the "side venting" suggested by another poster unless you can figure out how to get 3 square feet of venting out the sides. Most people use those little 3" vent plugs that might have a square inch of air space, if you're lucky.

    Note that this is NOT the case of "I can't do it completely, I'll do it partially". If you don't have enough area, then the air flow will be inadequate.
    Also, another problem is that most cathedral ceilings have skylights. These are blocked areas that cannot be vented without cleverness.

    If you are NOT venting under sheathing

    Contrary to popular opinion, venting is not necessary, and can do more harm than good if not implemented properly. Remember, the key is to keep the roof sheathing from getting wet. Most moisture is carried by air movement. For example, a recessed light installed in a cathedral ceiling is roof rot ready made.
    The best solution is to apply closed cell polyurethane spray foam directly to the underside of the roof sheathing. 2-3" is necessary in most climates, but see the Building Science literature for details. Closed cell polyurethane is a very effective vapor retarder when applied to these thicknesses. If moisture cannot reach the roof deck, you're in good shape (as long as the roofing above it is in good shape).
    The advantage to this solution, as noted, is that internal warm humid air can't even touch the sheathing, so it will never condense. This air seals and insulated. So, if you install recessed lights in the sheetrock below, you're still protected. Every other solution fails when you have ceiling penetrations, especially if you place a vapor barrier like plastic sheeting in the ceiling. Since the vast majority of moisture movement is at penetrations. If you install plastic sheeting, the electrician will cut a big hole in it where the recessed light pokes through. Since all such fixtures leak, unless extremely carefully detailed (never done), the air will leak into the cavity. With normal insulation (fiberglass), this moisture then gets trapped in the cavity by the plastic, rotting out your roof unless you have ample air flow to carry the moisture away.

    Another solution is to use dense packed cellulose. This is defined as ~3.5 pounds per cubic foot. Studies on thousands of homes (see Applegate insulation's website) have shown that fully filling the cathedral ceiling cavity minimizes air infiltration and provides a long lasting roof with good insulation. The key is that it has to be dense packed cellulose and there must be no venting into this space.

    This just touches on a couple key considerations. To summarize:
    If you're going to ventilate, you have to do it right
    If you use fiberglass, you have to ventilate
    If you use spray foam, you should not ventilate, nor should you use any other vapor barrier.
    If you use dense packed cellulose, do not ventilate or use vapor barriers.
    astrobiker's Avatar
    astrobiker Posts: 2, Reputation: 4
    New Member
     
    #10

    Dec 19, 2008, 11:34 AM
    Many people spray closed cell foam directly against the underside of the metal roof or roof deck. It's not the cheapest solution but it has many advantage - it gets in all the cracks, reduces noise, provides rigidity, keeps moisture from condensing on the roof deck etc.

    There are also a number of discussions about metal roofs here
    paragod39503`'s Avatar
    paragod39503` Posts: 1, Reputation: 1
    New Member
     
    #11

    Oct 25, 2010, 05:15 AM
    Comment on astrobiker's post
    Answered all my questions. You wouldn't happen to work with Mike Holmes? Lol

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search


Check out some similar questions!

Cathedral ceilings in a ranch [ 3 Answers ]

I just bought my grandmothers 1960 ranch. I would like to install a cathedral ceiling in the living room area, is this possible for a Do it yourselfer? It has bolted 2x6 W truss roof I am looking to do approx 15 foot wide section. Would a wall out of 2x4's for the sheet rock at the center beam be...

Attempting to install ceiling fan in older house [ 6 Answers ]

I'm attempting to install a Hampton Bay 42" ceiling fan but I'm having some weirdness with the house wires. House wires are: 2 white (attached to current light fixture) 1 red (attached to current light fixture) 2 black (capped off) The ceiling fan has the following wires: 1 black (fan...

Ceiling fan / house wiring [ 1 Answers ]

I'm attempting to install a ceiling fan with remote, but I'm having some problems with the house wires. House wires are: 2 white (attached to white wire of current light fixture) 2 black and 1 red wire (all attached to black wires of current light fixture) 2 copper grounds (attached to metal...

Hanging ceiling fan from vaulted ceiling peak [ 2 Answers ]

Want to install Hampton Bay's Berlini model 729395 on a cathedral ceiling with a single ridge beam. Want to hang fan from the peak and there's not enough room for the canopy to cover the hanger bracket. Is there any extenders for this?

Mice in ceiling of semi-detached house [ 1 Answers ]

Thanks for being an expert. I am a new owner of a semi-detached house. I have heard very occasional skittering in my living-room ceiling and suspect mice. I have looked both on the outside and inside the house, but can find no obvious entry point. Could the mice be in the walls and/or coming in...


View more questions Search