Ask Experts Questions for FREE Help !
Ask

Troubleshooting guide on a trane xe-80 furnace

Asked Nov 27, 2009, 03:12 PM — 9 Answers
I have a trane xe-80 furnace, And there is a code that flashes Thermal code protection. We have cleaned the heat sensors is there anythig else I can do to get heat till the Holiday weekend is over?/

Search this Thread
Share |
9 Answers
Joshdta's Avatar
Joshdta Posts: 2,453, Reputation: 230
Ultra Member
  
#2

Nov 27, 2009, 03:49 PM
Never heard of that fault, did you check the limit and flame roleout switches? WHat happens when you turn it on? Does the vent motor run? The blower motor? Does the ignitor glow?
Helpful
KC13's Avatar
KC13 Posts: 2,567, Reputation: 514
Ultra Member
  
#3

Nov 27, 2009, 06:44 PM
Did you check any of these?
Attached Images
   
Helpful
dpopgky's Avatar
dpopgky Posts: 2, Reputation: 10
New Member
  
#4

Nov 30, 2009, 09:45 PM
I have a tr90 having similar problem - 4 blinking lights. Have to reset flame roleout switch. Blower keeps running, blowing cold air until reset. Service man said furnace not sized for our 2800 sq ft home, too few vents, too small cold air return (1 - 16 inch). Could problem be one of the switches shown be defective? New USER, thanks for advice.
Helpful
masoodlo's Avatar
masoodlo Posts: 2, Reputation: 10
Junior Member
  
#5

Oct 26, 2010, 03:20 PM
The electric sparker dose't spark
I have to do it with a lighter
What shulld I do?
Helpful
Joshdta's Avatar
Joshdta Posts: 2,453, Reputation: 230
Ultra Member
  
#6

Oct 26, 2010, 04:12 PM
Stop before you blow yourself up!
Helpful
electrician2010's Avatar
electrician2010 Posts: 2, Reputation: 10
Junior Member
  
#7

Dec 3, 2010, 01:48 PM
I agree with Joshdta. Get a new flame detector or igniter. Both under 25 bucks.
Helpful
tendance's Avatar
tendance Posts: 5, Reputation: 1
New Member
  
#8

May 14, 2011, 06:32 PM
When my xe 80 turns on for air conditioning, we experience noise in the fan or motor
Helpful
YADY831's Avatar
YADY831 Posts: 1, Reputation: 1
New Member
  
#9

Nov 13, 2012, 10:18 AM
i got an Trane XE80 turnson fine but afrter 2mins. turns off the flames and motor stils goes on, and the light sensor flashes 4 times... can anybody can help me to fix my heather please... thank you...
Helpful
brcleveland's Avatar
brcleveland Posts: 1, Reputation: 1
New Member
  
#10

Feb 25, 2013, 01:12 PM
I have a TRANE XE 80 furance, is it normal for the control module to have a constant humming noise? It will continue to hum even after the thermostate is turned off.

The furnace has been operating intermittently. When it does not operate correctly the ignitor glows but it does not light. If I wiggle wires on the contol module it will ignite and continue to act normally for a few hours then act up again. If the humming noise in the control panel is not normal could that be my problem?

f
Helpful
Not your question? Ask your question View similar questions
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

Furnace troubleshooting [ 3 Answers ]

How do I locate my furnace relay switch?

Trane xc90 troubleshooting [ 9 Answers ]

My xc90 (the furnace) has sporadically worked on and off for the past couple of years. Right now it's not working at all..there is 24v at W but the inducer isn't coming on. The error code tells me there is a pressure switch issue but the green led flashes slowly indicating there is no call for...

Do trane gas Furnace have belt and how to fix trane gas Furnace [ 1 Answers ]

I have trane gas Furnace and its stopped working the pilot is not working its keep shutting off and also the switch on and off is working but the pilot and burner is not working what should I do ?:(

Trane XL14i 410a leak troubleshooting [ 2 Answers ]

I have a 410a leak with my Trane XL14i system. The leak has been there since the installation. Each season they need to add 410a. I have a HVAC company doing the troubleshooting for me. One of their techs told me that a Trane XL14i system shouldn't use dye to perform the troubleshooting....

View more Heating & Air Conditioning questions Search