Ask Experts Questions for FREE Help !
Ask
    Tmckeage's Avatar
    Tmckeage Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Apr 26, 2012, 06:00 PM
    Robert shaw reset
    I had a flammable gas present code flashing, I unhooked some wires now I have a miss wiring code, how do I reset?
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #2

    Apr 26, 2012, 06:31 PM
    A vague question only gets vague answers. If you can give the make and model # of your system, some one can help you. All systems wire deferent. If you had a fault code of rollout limit you have more than a mis-wired problem.
    Tmckeage's Avatar
    Tmckeage Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Apr 26, 2012, 06:55 PM
    Okay
    Tmckeage's Avatar
    Tmckeage Posts: 3, Reputation: 1
    New Member
    		  
    #4

    Apr 26, 2012, 07:00 PM
    It's a superflue hotwater tank with a Robert shaw gas valve. I had a code showing flammable gas present, it would light for a couple of second and then go out. I removed and un hooked the wires on the sensor by the air intake. Now I am getting a code of FVD interface failure/miswiring. Is there a 1 hour lockout period to wait for a reset? If I can get it to fire again I have to deal with the flammable Vapours code. Dirty ignition rod?
    oneoldjimmy's Avatar
    oneoldjimmy Posts: 2, Reputation: 1
    New Member
    		  
    #5

    Apr 28, 2012, 10:23 AM
    The flammable gas sensor is considered a wear item, once the detect, they should be replaced.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
    		  
    #6

    Apr 28, 2012, 12:01 PM
    Also, unhooking wires will only complicate the problem. Reconnect the other wires and start with the senser that was the original problem.
    T-Top's Avatar
    T-Top Posts: 1,871, Reputation: 100
    Ultra Member
    		  
    #7

    Apr 28, 2012, 08:50 PM
    Good info you gave about your system. Make sure your burner is clean along with a clean
    Flame sensor.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Robert shaw thermostat is reading E5, what does this mean and how do I fix it? [ 0 Answers ]

My robert shaw thermostat started reading e5. Does this mean something is wrong with the ac/heat pump unit itself or the thermostat and how do I fix it?

Cm260 robert shaw? [ 0 Answers ]

I am changing a robert shaw cm260 t-stat to a honeywell rth2300. The robt shaw had a red and yellow wire hooked to the A contact. There is no A on the honeywell, where do you hook them up. Or could you say what those wires do? The whole connection was blue wire to B, white to O, green to G, red and...

Robert shaw thermostat eheat setting [ 1 Answers ]

We recently bought a home with a robert shaw 303 thermostat controlling our heat pump and air handler. We had a number of trades in doing some renos and I think they have adjusted the heat. I was leaving set as it was by the previous owner. My concern is that when I look at the display, I don't...

Maple Chase / Robert Shaw 9620 [ 3 Answers ]

Let me start by saying this could either be a thermostat or a heater problem. We have a Maple Chase that's the equivalent of a Robert Shaw 9620. After reading different posts here, I found the correct owners manual online. Our problem is that the heater runs and runs but it's blowing very cold...

Change out old thermostat with a Robert Shaw RS5110 [ 1 Answers ]

I currently have a General Controls T-90 thermostat and I want to switch that with a RobertShaw RS5110. My current Thermo is wired with a Green wire going to F a Black wirre going to C a White wire going to H and a Red wire going to M. There is no diagram for this configuation. Does anyone have...

View more questions Search