|
|
|
|
New Member
|
|
Sep 3, 2007, 07:48 AM
|
|
Honeywell Chronotherm IV Plus Thermostat
How do I clear the flashing filter light on my thermostat? I have changed my filter.
|
|
|
Ultra Member
|
|
Sep 3, 2007, 08:39 AM
|
|
Press the "i" key, then the up arrow, then run program.
Here is a site for your operators manual; (Page 17) [url]http://honeywell.com.au/business/acs/acp/ecc/manuals/T8602_%28chronotherm I.pdf
Hope this helps, Mike
|
|
|
New Member
|
|
Jul 17, 2008, 01:39 PM
|
|
Originally Posted by lclovis
How do I clear the flashing filter light on my thermostat? I have changed my filter.
I read one post that was incomplete and confusing. The answer is... In fairly rapid sequence... Press the "i" button, then open up the flap and press the "^" button under "Time" and then press the "Run Program" button. That will clear the flashing "filter"
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 17, 2008, 03:09 PM
|
|
|
|
|
Ultra Member
|
|
Jul 18, 2008, 08:02 PM
|
|
Originally Posted by chaspierre
I read one post that was incomplete and confusing. The answer is...In fairly rapid sequence...Press the "i" button, then open up the flap and press the "^" button under "Time" and then press the "Run Program" button. That will clear the flashing "filter"
You copied my answer to to a question posted by another person and said it was incomplete! Can you read? Or do you need an interperter?
|
|
|
New Member
|
|
Jan 1, 2009, 01:42 PM
|
|
How do I get rid of the flashing filter sign after I have already replaced the filter
:confused:
|
|
|
New Member
|
|
Apr 17, 2012, 02:55 PM
|
|
This did not work -- Filter light is still blinking
|
|
|
New Member
|
|
Feb 25, 2013, 07:06 AM
|
|
After you press the "I" button, you will get a reading that states the number of days remaining for "Air", this refers to the days remaining before the air filter change is supposedly needed. If the "filter" is flashing, the number is probably "0". Using the up arrow next to "wake", increase that 0 to as high a number you can, usually 30 or more. Then press "run program." This will get rid of "filter" for those number of days. Then you need to repeat.
|
|
|
New Member
|
|
Nov 19, 2013, 04:28 PM
|
|
How do you use the copy function?
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Filter reset button for Honeywell Chronotherm IV plus
[ 13 Answers ]
I just changed the filter in my furnace, how do I reset my thermostat to make the word "filter" stop blinking. I called the service dept. and they told me to find my users manual! I can't find it. HELP!
Honeywell Chronotherm IV Plus Honeywell Thermostat, T8624D
[ 1 Answers ]
Honeywell Deluxe Programmable Multistage Thermostat, #T8624D
Chronotherm IV Plus
I have 2 of above thermostats and have had for about 5 years. It takes no batteries and is directly connected to a 24 volt source.
Have one upstairs and one downstairs.
Have noticed at times that the LCD on...
Wiring a Honeywell Chronotherm IV
[ 3 Answers ]
What size wiring do you use for a thermostat? I need to move one from an exterior wall to an interior one. Also, any tips on fishing wires through insulation? Bringing it up the wall and over suspended ceiling and down another wall.
Common Wire on Honeywell T8624D Chronotherm
[ 1 Answers ]
I'm replacing two White-Rodgers thermostats, one heating and one cooling with a Honeywell T8624D heating/cooling thermostat. I have three wires coming from the cooling thermostat (W, R & G) and 2 wires for heating coming from the transformer located in the wall at the thermostat which are both...
View more questions
Search
|