|
|
|
|
New Member
|
|
Nov 10, 2007, 10:06 PM
|
|
Heil furnace schematic and directions for parts install
Where can I find a good schematic or diagram of the parts within a Heil furnace? Also, when purchasing parts, do they come with installation directions? I always want to try the initial install myself rather than paying for service calls first.
|
|
|
Ultra Member
|
|
Nov 10, 2007, 10:36 PM
|
|
Most furnaces have a legand glued to a door that tell what the parts are, most, now,, parts don`t come with installation instructions,, if you go to replacing parts hoping to sooner or later replace the right part,, could get very expensive,, would probably save you money to call a technician
|
|
|
New Member
|
|
Dec 20, 2009, 02:15 PM
|
|
Originally Posted by wmproop
most furnaces have a legand glued to a door that tell what the parts are,,most,,now,,,parts don`t come with installation instructions,,,,if you go to replacing parts hoping to sooner or later replace the right part,,,could get very expensive,,,would probably save you money to call a technician
There is not one on the door am I screwed now
|
|
|
New Member
|
|
Dec 20, 2009, 02:17 PM
|
|
There is not one can I give the s# and m# and you send me one
|
|
|
New Member
|
|
Feb 9, 2010, 04:51 PM
|
|
Flame comes on ,fancomes on flame goes out .fan goes off flame comes back on
|
|
|
Ultra Member
|
|
Feb 9, 2010, 04:56 PM
|
|
Try cleaning the flame senser,
|
|
|
New Member
|
|
Feb 10, 2010, 05:39 AM
|
|
This heil furnace is 60 years old
|
|
|
Heating & Air Conditioning Expert
|
|
Feb 10, 2010, 05:50 AM
|
|
Exact model number needed for schematic if available.
|
|
|
New Member
|
|
Feb 10, 2010, 07:03 PM
|
|
Heil model# bg 80
|
|
|
Heating & Air Conditioning Expert
|
|
Feb 10, 2010, 07:14 PM
|
|
No B series ever made by Heil. Post some pictures of what you have. Might be able to find something similar for wiring.
|
|
|
New Member
|
|
Feb 26, 2010, 08:22 AM
|
|
F
Originally Posted by dphv
flame comes on ,fancomes on flame goes out .fan goes off flame comes back on
Flames sensor' good range .5 to .8 vdc
|
|
|
New Member
|
|
Jun 22, 2010, 05:14 AM
|
|
Fan run constantly Even with t-stat turned off
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Heil Furnace
[ 10 Answers ]
I have A Heil Furnace that starts up just fine Model #NDG1075DFo1, but after its running for 5 minutes or so it gets another call for heat, fills the gas box with naatural gas and re-lights this mix pretty violently. This may happen a few times during the heating cycle until the thermostat is...
HEIL furnace
[ 1 Answers ]
Our heil furnace won't stay lit. It goes out after we release the pilot button. Any suggestion?
Forgot to install parts of pool
[ 2 Answers ]
Okay my husband recently installed a pool with no instructions. He forgotto install the strips that go over the screws on the crease. One should have gone on the outside and on on the insude under the liner, is it so important we should drain it and start over?
Please help,
Mandy
Heil furnace
[ 2 Answers ]
I have bought a house with a furnace and I cannot get the pilot to light. I am asking for some type of manual so I can figure this out.
The model is VG-80MD-1 and the serial is H73838067.
The house was built in 1977 and I am sure this is the original
Thanks for any info
Blower won't come on Heil furnace
[ 2 Answers ]
I have a heil furnace in a home I just purchased. The first day it worked fine. Second day, it fires up, I can hear a motor running, but the blower doesn't come on. Relay switch?
Thank You!
View more questions
Search
|