Ask Experts Questions for FREE Help !
Ask
Page 1 of 2 1 2 >

Comfortmaker gne100f14a1 water in hose from pressure switch

Asked Feb 22, 2012, 01:30 PM — 10 Answers
Why is there water in the hose between the inducer motor and the pressure switch on my comfortmaker gne100f14a1

Search this Thread
Share |
10 Answers
wmproop's Avatar
wmproop Posts: 3,732, Reputation: 554
Ultra Member
  
#2

Feb 22, 2012, 02:47 PM
sounds like drains aren`t just like they should be. Is it a new install?
Helpful
prib25's Avatar
prib25 Posts: 6, Reputation: 10
Junior Member
  
#3

Feb 22, 2012, 03:40 PM
About ten years old. Not sure what drain you are talking about.
Helpful
mygirlsdad77's Avatar
mygirlsdad77 Posts: 5,541, Reputation: 1650
Plumbing Expert
  
#4

Feb 22, 2012, 04:05 PM
If this unit is 90+ efficiency unit, it will have a drain system which can clog and cause condensate water to back up into the draft inducer and therefore up into the pressure switch tube. If you have a 90+, clean any and all drain ports and hoses in your furnace, along with the drain pipe on the outside of the furnace.
Helpful
prib25's Avatar
prib25 Posts: 6, Reputation: 10
Junior Member
  
#5

Feb 22, 2012, 04:25 PM
This furnace is a 80 percenter
Helpful
wmproop's Avatar
wmproop Posts: 3,732, Reputation: 554
Ultra Member
  
#6

Feb 22, 2012, 06:24 PM
80 percenter,with an inducer motor,and pressure switch,I haven`t run up on that at all or at least very often.
is there anything about this furnace you failed to tell us,,,so as a 80% furnace it has metal exhaust,,does it have a ac a-coil that sits on top of furnace? does the exhaust/flu pipe go straight up ? into a chimney flu?
Helpful
prib25's Avatar
prib25 Posts: 6, Reputation: 10
Junior Member
  
#7

Feb 22, 2012, 06:43 PM
Im sorry it must be 90+. I do not know where the inside drains are located to clean them. It has a metal inducer motor
Helpful
prib25's Avatar
prib25 Posts: 6, Reputation: 10
Junior Member
  
#8

Feb 22, 2012, 07:01 PM
Im sorry i couldnt provide more knowledgeable info. Tomorrow i will post pictures perhaps that would help me to show exactly what i have, since im not really sure. Thank you for your help thus far
Helpful
prib25's Avatar
prib25 Posts: 6, Reputation: 10
Junior Member
  
#9

Feb 22, 2012, 07:31 PM
It has a metal flue pipe to the chimney and a metal inducer motor. I know this for sure.
Helpful
wmproop's Avatar
wmproop Posts: 3,732, Reputation: 554
Ultra Member
  
#10

Feb 23, 2012, 04:35 AM
its probably 80%,,,with metal vent pipe,,,,but use close-up photoes might help,,,maybe mygirlsdad,will have some input,,he likes photo`s
Helpful
Not your question? Ask your question View similar questions
 
Page 1 of 2 1 2 >
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

Goodman Furnace - 3 Blinking lights, solid light w/suction on hose to pressure switch [ 2 Answers ]

Hello, I have 3 blinking lights on a Goodman GMNT080-4B gas furnace. An online manual says this is caused by "PRESSURE SWITCH FAILURE TO CLOSE" and to check: "VENTER, PRESSURE SWITCH, VENT BLOCKAGE". One potentially useful bit of diagnostic information is that if I suck on the hose going...

After changing hot water hose turned water on no pressure in my house [ 1 Answers ]

If you let it sit it builds up for aout 2min then it gradule goes away until its just a drip

Water pressure too high for garden hose? [ 1 Answers ]

Hi, I don't know what the water pressure is at my house, but I do know that it is very high/ strong. We live near the water plant- I assume that has a lot to do with it? We've been through several garden hoses in the last couple years. We've bought regular hoses and the last one we bought was...

Water Pressure - hose bib [ 3 Answers ]

After a driveway contractor used a power washer on our driveway, the hose bib he was connected to lost water pressure. I had the lawn sprinkler on before he came, pressure was great, and put it back on after he left, pressure was at about 50%. The other hose bibs, and all pressure inside the...

View more Heating & Air Conditioning questions Search