Ask Experts Questions for FREE Help !
Ask

Bryant Model 350MAV Furnace

Asked May 12, 2008, 01:08 PM — 3 Answers
Hi, I recently had a furnace repairman in who told me our inducer on our Bryant Model 350MAV furnace needed to be replaced. He said the total cost would be $1075.00, including $890.00 for the inducer. This seemed high to me. Can anyone give me an idea of what this repair should have cost, please? Perhaps, I am just naive but I am ready to replace it myself. Is this a difficult or dangerous repair to make? Thanks for any and all info.

Search this Thread
Share |
3 Answers
hvac1000's Avatar
hvac1000 Posts: 14,546, Reputation: 2381
Heating & Air Conditioning Expert
  
#2

May 12, 2008, 06:06 PM


Replace it yourself.
Here are the install instructions

http://www.docs.hvacpartners.com/idc...t/58m-94si.pdf

MOTOR

eBay Express: NEW INDUCER MOTOR KIT FOR CARRIER, PAYNE, BRYANT - Description

Motor instructions only

http://www.ballrefrigeration.com/htm...er%20motor.pdf

Assorted for sale

Bryant inducer, Tools Home Improvement, Home Garden items on eBay.com

Have fun. The job is not that hard. Turn off power to furnace before working on it.
Helpful
davidbnelson's Avatar
davidbnelson Posts: 4, Reputation: 1
New Member
  
#3

May 13, 2008, 04:03 AM
Thanks! This is a big help and I appreciate it. We don't have $1000 to spend on this repair and this solution makes it affordable. I will throw the circuit broker for the furnace. Should I cut off the gas, also?
Helpful
hvac1000's Avatar
hvac1000 Posts: 14,546, Reputation: 2381
Heating & Air Conditioning Expert
  
#4

May 13, 2008, 04:48 AM


Really no need to cut off the gas because the gas cannot come on without the electric being on. Follow directions exactly. This should save you big time on the costs to repair your furnace.
Helpful
Not your question? Ask your question View similar questions
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

Bryant Furnace model 383KAV won't kick on [ 10 Answers ]

I'm not getting any error led blips from the computer board. I can only see one limit switch which isn't tripped. I replaced the thermostat but that wasn't it. I've checked breakers and even tried tripping them off and then back on. Usually if I remember right this furnace goes through a...

Bryant gas furnace model 383 KAV sometimes does not run [ 6 Answers ]

I have a 10 year old Bryant gas furnace model 383 KAV that sometimes does not run. The inducer motor does not come on and there are no codes. If I cycle the power several times it will eventually all work normally at least until the next morning when it may or may not restart after being off at...

Location of the flamer sensor in a Bryant Model 383K Furnace [ 3 Answers ]

Where is the exact location of the flamer sensor in a Bryant Model 383K Furnace? Is there a better diagram than I currently have in my user's manual? It is really for the installer. I know that I need to sand down/ steel wool the flame sensor, but can't remember the location. Thanks in...

Bryant gas heater model beginning 310aav [ 3 Answers ]

I had not used my furnace over the summer. Before turning on the thermostat, I replaced the filter and checked to make sure red light was on solid. Turned on thermostat and furnace light started blinking error code 23, which according to list on furnace means pressure switch obstructed or off. I...

View more Heating & Air Conditioning questions Search