|
|
|
|
New Member
|
|
Jul 18, 2008, 11:37 AM
|
|
Bryant AC blower fan motor "quick" cycling
While running in AC mode or fan ON mode the blower fan keeps cycling on/off contiuously for on off periods from less than a second to several minutes.
I figured the motor was overheated (bad windings) so I replaced the motor and capacitor with poor results.
It seems to run longer but contiues to "quick" cycle... acts like a bad wire connection or something.
Any ideas on next steps...
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 18, 2008, 11:59 AM
|
|
What is the brand and model number of your thermostat?
|
|
|
New Member
|
|
Jul 18, 2008, 12:25 PM
|
|
It is a lux 9000
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 18, 2008, 12:48 PM
|
|
There are three different models of 9000 thermostats. Can you be more accurate. I need the complete correct model.
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 18, 2008, 12:51 PM
|
|
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 18, 2008, 12:54 PM
|
|
If it is not the thermostat it could be a low voltage/thermostat wire shorting out causing this.
Do you have a circuit board in your unit?
What is the indoor section model number
|
|
|
New Member
|
|
Jul 18, 2008, 01:54 PM
|
|
It is neither of these listed onn their website they are TX9000 mine is a lux 9000.
I don't see it listed, even in the discontinued, and have inquired with them as to what I have.
Yes there is a circuit board in the cabinet with the blower. I will look for the model number.
|
|
|
Ultra Member
|
|
Jul 18, 2008, 02:41 PM
|
|
If you would please explain what the blower does when you turn the fan to "ON" and the AC is in the "OFF" position.
Leave it that way for five minutes and then feel the motor, for heat.
Also does the blower do the same thing when the heat is turned on?
|
|
|
New Member
|
|
Jul 18, 2008, 05:42 PM
|
|
The fan was staying on even when the thermostat was in the system off mode.
I looked closely at the internal circuit board that hvac1000 had asked about.
It had moisture on it. The drain line was slightly plugged causing water to pool and run down on the board.
I cleaned the drain and dried out the board with an air line and all is good. Operating fine now. Thanks... hvac1000 and letmetellu
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 18, 2008, 06:02 PM
|
|
I hope the board holds up. Sometimes when they get water on them they eventually die. At least now you know what part to replace.
|
|
|
Ultra Member
|
|
Jul 19, 2008, 12:46 PM
|
|
Where the water was on the board it might be a good idea to clean the area more to remove any residue and then cover the area with a clear fingernail polish.
|
|
|
Heating & Air Conditioning Expert
|
|
Jul 19, 2008, 03:20 PM
|
|
That is a good idea letmetellu. In the past I have actually put circuit boards in the oven at low temperature to force the drying issue.there is also a spray can of electronic parts cleaner that has the pressure to blow the water out and then safely evaporate leaving a very lite film of protection that prevents the relay contacts from going bad. Clear laquer spray to coat the board was the last step
.
We used cases of that stuff during the flood of 1997 on electric main panels and circuit breakers to clear out the water and help prevent corrosion.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Fan Blower not working in "ON" or "AUTO" in heat or AC
[ 13 Answers ]
Got home from the Brewer game this afternoon and noticed the house was warm(78). Outside was 91. I checked the T-stat and it was set correct. Noticed the air vents weren't blowing anything. Went outside and the condenser and fan was running fine. Then I went downstairs to the furnace unit to see...
Intertherm Electric Furnace Blower works in "on" not in "auto"
[ 6 Answers ]
I have an Intertherm Electric Furnace E2EB-015AH. I came home from work last night, turned the heat on and it didn't work as advertised. I could hear the relays clicking occasionally so I investigated a little and found the elements are heating up and cycling, the relay inside the thermostat cycles...
Bryant furnace: thermostat showing "AC", house cold, fixed (for now.)
[ 1 Answers ]
System: Bryant 333BAV 80 plus furnace, 10 yrs old, with Honeywell Chromotherm III thermostat. No problems with either in the past. Minnesota. January.
Upon waking up this morning, found the house was 58 degrees, with set point at 68. Checking the thermostat, found it was showing "AC" (power...
Blower runs on "ON", but not on "Auto"
[ 3 Answers ]
Hello All,
I have a Goodman COMBINATION HEATING AND COOLING OUTDOOR UNITS PG/PGX SERIES (100K BTU). It failed to warm the space. The fan would not run on “ON” or “Auto” mode. Upon investigating, there is no power to the unit due to 25 amps fuses blown. Replaced with new fuses. Power was...
View more questions
Search
|