Ask Experts Questions for FREE Help !
Ask
    markfoil's Avatar
    markfoil Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Jan 28, 2010, 08:05 AM
    Can I convert a 120 outlet to 240
    I just moved and the house is set up for a gas dryer, I have an electric dryer. Can I convert my existing 120 outlet to support a 240 outlet, or do I need to run new wire.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
    		  
    #2

    Jan 28, 2010, 08:52 AM

    You need a new wire, breaker and receptacle.

    A "standard" 120v receptacle is completely different from a 30A-120/240v 4-wire dryer receptacle.
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
    		  
    #3

    Jan 28, 2010, 09:06 AM
    Absolutely not!

    A new four wire circuit must be run. You need to know the amperage required by the dryer to properly size the circuit. Also, a 20 amp 120 VAC is required to be installed in the laundry room.

    If the dryer requires 30 Amps, then a 10/3 AWG cable must be used. Also, you will need a DPDT 30 Amp breaker to be installed in the Main Service Panel. <corrected amperage ratings and cable size. Brain dead monment!!>

    The receptacle should be a 50 Amp receptacle for a four prong plug.

    Black will go to one load position. Red will go to the second load position. White goes to the Neutral pin and Green green goes to the Ground pin.

    If you do not know how to work on a Main Service Panel, then I strongly suggest that you contact several licensed electricians to plan and run your needed circuits.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
    		  
    #4

    Jan 28, 2010, 09:08 AM

    Don, just a question. When have you seen a dryer that required a 40A circuit?
    Aside from commercial and funky European models, 99.9% of the ones I have seen were 30A.
    donf's Avatar
    donf Posts: 5,679, Reputation: 582
    Printers & Electronics Expert
    		  
    #5

    Jan 28, 2010, 09:26 AM

    Stan,

    Just an answer, never! Thank you. I will edit the item.

    I was using the 40 amp rating as an illustration because for the life of me, I did not rember the 30 Amp rating.

    I even checked the 2008 NEC and could not find it. Call it a very senior moment.
    stanfortyman's Avatar
    stanfortyman Posts: 5,598, Reputation: 279
    Electrical & Lighting Expert
    		  
    #6

    Jan 28, 2010, 09:44 AM

    Hey, no problem. I was really just wondering.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Convert 4 prong 240 generator outlet to 3 prong [ 6 Answers ]

How do I make an extension cord from my 4 prong 240 twist generator outlet to a 3 prong 240 outlet for my radial arm saw?

How to change a 120 volt outlet to a 240 volt outlet [ 1 Answers ]

I have a 240 volt, single phase, 3 wire, 10 amp, 60 hz battery charging system for a small electric car but have no 240 volt outlet. I do however have a 120 volt outlet. How can I change the 120 volt outlet to accommodate the 240 volts? I know I will have to get a new outlet, but I am asking about...

Change a 120 to a 240 outlet [ 1 Answers ]

Please help.. in my gerage all I have are 3 or 4 outlets all normal 120 household outlets, I'm going to start welding at my house to keep up with work and my welder needs a 240 outlet. I have a late 80's early 90's fuse box and not 1 240 outlet in the entire house, how can I myself install a 240...

120 volt outlet from 240 volt outlet [ 1 Answers ]

I understand that it is possbile to wire a 120 volt outlet from a 240 volt outlet. My 240 volt outlet has 3 wires in, white, black, and a ground. Do I wire the 120 volt outlet from the either wire and the ground? My voltage meter indicates that connection is 120 volts. Is there any down side to...

Replacing a 240 volt outlet with a 120 volt oulet [ 1 Answers ]

We've switched to a central air conditioning system and no longer need the 240 volt outlet by the dining room window. The house was built in 1928, updated in 1957, and again a couple of ad hoc times thereafter. The wiring is at times very old, brand new or somewhat old. My guess is that the 240...

View more questions Search