Ask Experts Questions for FREE Help !
Ask
    ckwense11's Avatar
    ckwense11 Posts: 2, Reputation: 1
    New Member
     
    #1

    Feb 12, 2007, 11:02 AM
    Dry wall screws popping out
    I am only 2 months into a newly built home and the screws that were used for the drywall appear to be popping out in several places. I have seen an earlier post about nails and the reply suggested screws, but these screws are coming out too! Is this normal for a house only 2 months old? What do I need to tell the builders to do to rectify this situation so I can know if there is a major issue that may happen after the year warranty!
    cjcdallas's Avatar
    cjcdallas Posts: 63, Reputation: 6
    Junior Member
     
    #2

    Feb 12, 2007, 07:11 PM
    Are you sure the screws are popping out? I have never seen that happen but I guess it could. Usually the nail pops are caused by flexing of the wood during shrikage and expansion. I personally have not seen that ever happen with screws.
    Usually the builder will do a walk through every 3-6 months and make repairs until the warranty is up. I would encourage you to mark each spot that has an issue to identify it so you can point them out when they come.
    ckwense11's Avatar
    ckwense11 Posts: 2, Reputation: 1
    New Member
     
    #3

    Feb 12, 2007, 08:49 PM
    Thanks for the response. I thought it strange too, but one of them popped the drywall out and you could clearly see the screw. I called the builder to come out and showed multiple areas that are appearing throughout the house. I'm afraid this is the just the tip of the iceberg with issues on this house.
    jujubrose's Avatar
    jujubrose Posts: 21, Reputation: 1
    New Member
     
    #4

    Feb 24, 2007, 09:02 PM
    Drive them back in. Most likely they were not screwed all the way in. This does happen their could have been something behind the board like a shim at the time it was screwed in. And now it has falled leaving the board to flop just a bit on the wall. Push on the board if it gives a bit then you got it. It is a screw and they usually do not come out once driven stupid screws.

    Then they could have missed the board all together it is simple and part of owning a home. It is built of wood and concrete buy people. It was not meant to fly or float or go into space it will not be perfect ever. You will be much happier if you get a bucket of sheetrock mud and a screw gun and just fix it yourself it will save you a lot of aggravation to just tend to it. This is why we have tool collections human flaws terrible thing. Find perfection in imperfection. I know corny but what the hey

    Have fun Julie
    nmwirez's Avatar
    nmwirez Posts: 453, Reputation: 20
    Full Member
     
    #5

    Feb 26, 2007, 04:00 PM
    If this is a new stickframed house, there could be warpage of studwalls from an incomplete drying out of wood that is causing settling or oil canning of the sheetrock. If this is a developed neighborhood project, check out the next door construction too.
    The new house should have a 12 months warranty period to get things fixed. Do not attempt to do the fixes yourself, this will nullify the house warrantee. If this is a custom house owner-builder, well, good luck in getting the subs to come back for repairs unless they are legitimate and righteous. Sounds like the rockers didn't suck the sheetrock in far enough if the mudwork is popping out. The contractor should make this good in the eyes of the State licensing Board in general if done by permit.
    glavine's Avatar
    glavine Posts: 895, Reputation: 87
    Senior Member
     
    #6

    May 19, 2007, 11:18 AM
    1 Of 2 Things The Screws Were In To Deep To Start And There Not Holding The Drywall To The Studs. (my First Guess)
    Or You Have Some Bowed Studs In The Wall The Screws Just Aren't Holding , Hope This Helps , Nichols Trim
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #7

    May 22, 2007, 05:13 PM
    I agree with screws not tightened, Mudded and painted, and later someone bumped into wall. Maybe

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Maytag Dryer does not dry in Auto Dry mode [ 23 Answers ]

My Maytag dryer works well in the Timed Dry mode but in the Auto Dry mode it runs forever and does not dry well. In the Timed Dry mode it produces plenty of heat and works fine. What is happening in the Auto Dry mode that does not make the heat properly get to a level that allows the clothes to...

Running in wall Coaxial Cable from Existing wall [ 7 Answers ]

Hi there, Is there someone here who is expert on electrical? I need help on running coaxial cable to my existing walls. I have a 1st floor where I have access to drilling holes into the second floor. I am willing to cut open holes for installing the single gang boxes. Now, here are my...

Replaced liner now skimmer screws are stripped [ 2 Answers ]

Replaced a liner very old pool had brass screws and brass skimmer plate found 4 screws are stripped how to fix without replacing entire skimmer. Won't need to repair until spring when my customer will open his pool. Thank you Mike

Accord 2003 - Air filter screws stuck [ 1 Answers ]

I just broke 2 phillips screwdrivers attempting to remove the air filter cover of my Accord 2003. Only one screw unlocked. Bad move, I used an impact driver on another one and lightly broke the pastic casing. It still seems usable. How do I remove these screws? Is drilling the screws off the only...

Tried to remove strainer, screws snapped [ 2 Answers ]

I tried to remove the strainer in our stall shower today to get in there and clean out the drain; the house is 50 years old (but new to us) and I don't think the strainer had been removed in a long time (if ever). It's about 3" in diameter, held in by two screws opposite one another. The screws...


View more questions Search