Question
 | | | | | 
Feb 18, 2007, 06:09 AM
| | New Member  | | Join Date: Feb 2007
Posts: 5
| | | got power to ecu, still no spark
I finally found time to check the civic, found a bad fuse under the dash, replaced it, got power to the ECU, but i still dont get any spark. As i said last post I put the main relay, coil, and ignitor into my acura and it ran fine. Now i took the ecu and tried it in the acura,it started fine, so i assume that it is fine. The only thing i can come up wih is the sensors in the distributor have failed. Any ideas would be great. THANKS EVERYONE
| | | | | | |
Answers
| | | | | |
Feb 18, 2007, 06:38 AM
|
#2
| | | Cars & Trucks Expert
Join Date: Jun 2006 Location: Undisclosed, Republic of Texas
Posts: 5,085
| When you turn the ignition switch to ON, does the CEL come on and then go off after 2 seconds? |
 | | | | | | | | | | | | |
Feb 18, 2007, 06:42 AM
|
#3
| | New Member
Join Date: Feb 2007
Posts: 5
| yes , the light goes off after 2 sec | |
| | | | | | | | | | | | |
Feb 18, 2007, 06:45 AM
|
#4
| | | Cars & Trucks Expert
Join Date: Jun 2006 Location: Undisclosed, Republic of Texas
Posts: 5,085
| Agree that it sounds like a problem with the sensors in the distributor. Recommend using your old igniter, coil, and rotor in a new Honda distributor housing ($125). | |
| | | | | | | | | | | | |
Feb 18, 2007, 06:59 AM
|
#5
| | New Member
Join Date: Feb 2007
Posts: 5
| Thanks for the response, whats the chance thendist out of my 90 acura twin cam would be the same as the one in the 90 civic single cam, just to check it before I buy a new one? Once again thanks for the help! | |
| | | | | | | | | | | | |
Feb 18, 2007, 12:53 PM
|
#6
| | | Cars & Trucks Expert
Join Date: Jun 2006 Location: Undisclosed, Republic of Texas
Posts: 5,085
| Don't know. | |
| | | | | | | | | | | | |
Feb 18, 2007, 01:45 PM
|
#7
| | New Member
Join Date: Feb 2007
Posts: 5
| Quote: |
Originally Posted by beach nut I finally found time to check the civic, found a bad fuse under the dash, replaced it, got power to the ECU, but i still dont get any spark. As i said last post I put the main relay, coil, and ignitor into my acura and it ran fine. Now i took the ecu and tried it in the acura,it started fine, so i assume that it is fine. The only thing i can come up wih is the sensors in the distributor have failed. Any ideas would be great. THANKS EVERYONE | took the dist out of the acura.....of course it was different. Put the honda dist back in and tried just to see...... still no fire but i did finally get two trouble codes i think i read them right hello flash.......pause 15 flashes........pause 20 flashes then repeates. I took that as code 15 & 20 cant seem to find a list of codes | |
| | | | | | | | | | | | |
Feb 18, 2007, 08:17 PM
|
#8
| | New Member
Join Date: Jan 2007
Posts: 19
| hmmm, thats wierd. I also have a crx that is flashing code 20 and that code is supposed to be
electrical load detector
I dont know what code 15 is though unfortunatly. IF you figure this code out, or where to find this problem, please let me know. I'm looking for it also! | |
| | | | | | | | | | | | |
Feb 18, 2007, 08:28 PM
|
#9
| | New Member
Join Date: Jan 2007
Posts: 19
| OK, well, don't say I never helped out. here is your code 15
15 No ignition output signal - possible faulty igniter. | |
| | | | | | | | | | | | |
Feb 18, 2007, 08:30 PM
|
#10
| | Cars & Trucks Expert
Join Date: Jun 2006 Location: Undisclosed, Republic of Texas
Posts: 5,085
| Code 15: Ignition Output Signal. Likely, igniter problem.
Code 20: Electrical Load Detector. | |
| | | | | | | | Thread Tools | | | | Display Modes |  Linear Mode | |
