Check out these tips and explanations from our Cars & Trucks Expert; the best Cars and Trucks guy on the net!

Of course, you're also welcome to post questions to this board for more information: Just click the "Ask about Cars & Trucks" button (NOT the Answer this Question button) at the top of the page. Be sure, though, to check the list below to see if your issue is already covered.

Members: Please do not post replies in this thread. If you have a question, click on the Ask About Cars & Trucks button above.

txgreasemonkey

GGG. Honda Idle Control System

Idle speed is controlled by the Idle Air Control Valve (IACV). The IACV changes the amount of air being bypassed to the intake manifold, in response to electric current controlled by the ECM. When the IACV is activated, the valve opens to maintain proper idle speed.

Symptom and Subsystems to Check:

1. Difficult to start engine, when cold--check Fast Idle Thermo Valve.

2. Fast idle out of spec, when cold:
a. Check Fast Idle Thermo Valve.
b. Check IACV.
c. Check idle adjusting screw (see Section C).

3. Rough idle:
a. Check hoses and connections.
b. Check IACV.

4. RPM too high, when warm:
a. Check IACV.
b. Check Fast Idle Thermo Valve.
c. Check hoses and connections, check Power Steering Pressure Switch Signal, and check idle adjusting screw.

5. RPM too low, when warm:
a. Idle speed is below specified rpm, with no load--check IACV and idle adjusting screw.
b. Idle speed doesn't increase after initial start up--check IACV.
c. Idle speed drops in gear (automatic transmission)--check automatic transaxle gear position switch signal.
d. Idle speed drops when AC is on--check air conditioning signal and IACV.
e. Idle speed drops when steering wheel is turned--check power steering pressure switch signal and IACV.
f. Idle speed fluctuates with electrical load--check hoses and connections, IACV, and Alternator FR Signal.

6. Frequent stalling, while warming up--check IACV and idle adjusting screw.

7. Frequent stalling, after warming up--check idle adjusting screw and IACV.



Additional Steps:

. Check Alternator FR Signal. Have alternator inspected, if idle speed fluctuates with electrical load. The FR signal communicates to the ECM how "hard" the alternator is working to meet the electrical demands of the car, including the battery and any loads which aren’t monitored by the ELD. This square-wave signal varies in pulse width, according to the load on the alternator. The ECM places, approximately, 5 reference volts on the wire. The voltage regulator will drop this signal to approximately 1.2 volts, in proportion to alternator load. The ECM compares the electrical load (ELD) signal with the FR (Charging Rate) signal from the alternator and uses that information to set the idle speed and turn the alternator on and off. This helps fuel economy.

. Clean main ECM ground on thermostat housing.

. Reset ECM, by removing the 7.5 amp Back Up Fuse, in the under-hood fuse box, for 10 seconds.

. Replace Engine Coolant Temperature (ECT) Sensor, which affects fuel injector pulse width. It's located on the thermostat. The ECT Sensor is a temperature dependant resistor (thermistor), whose resistance decreases as the engine coolant temperature increases. It provides a richer mixture when cold, leaner mixture when hot.

. Replace PCV Valve, cleaning hose with brake cleaner spray.

. Substitute a known-good ECM. If symptom goes away, replace original ECM.

txgreasemonkey

HHH. Preventing Coil-On-Plug (COP) Problems

Many repair shops are reporting a large number of coil-on-plug (COP) failures with engines. The majority of problems are related to 1) customers washing their engines, or 2) body repair shops hosing off engines after repairing hood hail damage. Water seeps into the spark plug hole, where engine heat converts it to steam, and damages the coil.

Here are some rules to prevent the problem:

1. Never wash the engine, unless you cover the coils.

2. Always replace spark plug boots, when you change plugs.

3. Always replace the spark plug, when you replace a coil.

4. Always apply silicone dielectric grease to the rubber seal on the coil, where it connects to the engine; e.g., Motorcraft Silicone Brake Caliper Grease and Dielectric Compound (XG-3-A).