Ask Experts Questions for FREE Help !
Ask

94 eagle vision limp mode

Asked Feb 4, 2007, 06:35 AM — 1 Answer
HELP! My 1994 eagle vision dropped in to limp mode (2nd gear on trans) about a year ago... And at that time, I noticed a difference between the wiring diagrams on the 1994 vs the 1995 whereas the 95 had a separate 12v lead going to the "auto shut down" relay.
I added this lead and the trans started to shift fine again.
But now... The trans is stuck in 2nd again (and the lead that I added is still supplying 12v to the "ASDR"). I get a MIL code of "47" indicating that my charging voltage is too low, but my battery is charging just fine. I don't know if this has any relavance or not. Does anyone know what I can try next?

Search this Thread
Share |
1 Answer
bikerguy's Avatar
bikerguy Posts: 87, Reputation: 68
Junior Member
  
#2

Feb 4, 2007, 07:42 AM
If the wire had been upgraded on the diagram, There may be move of a draw than you think,are you sure you still have a Good clean secure 12 volt supply. Just checking with a meter won't assure of a good connection unless you get it on a digital meter at the source to the hundreds of a volt then go to the oter end to see if the is a voltage drop...Did you use crimp connections they should be cleaned and soldered. What gauge wire did you use. Look for the obvious.
Helpful
Not your question? Ask your question View similar questions
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Add your answer here.

Remove Text Formatting
 

Undo
Redo
  
Decrease Size
Increase Size
Bold
Italic
Underline
Align Left
Align Center
Align Right
Ordered List
Unordered List
Decrease Indent
Increase Indent
Insert Email Link
Wrap [QUOTE] tags around selected text
Wrap [CODE] tags around selected text
Wrap [HTML] tags around selected text
Wrap [PHP] tags around selected text
Wrap [YOUTUBE] tags around selected text
Notification Type:



Check out some similar questions!

Furnace turns off at 'ON' mode and will not operate at 'AUTO' mode [ 6 Answers ]

The furnace will not turns on at "ON' mode. After some reading, I thought it would be the pilot light that has gone out. I re-lighted the pilot light to see blue-red flame, but the furnace will turn off AGAIN after 3-4 hrs. Replaced a new Honeywell non-programmable thermostat today with the...

Furnace turns off at 'ON' mode and will not operate at 'AUTO' mode [ 2 Answers ]

The furnace will not turns on at "ON' mode. After some reading, I thought it would be the pilot light that has gone out. I re-lighted the pilot light to see blue-red flame, but the furnace will turn off AGAIN after 3-4 hrs. Replaced a new Honeywell non-programmable thermostat today with the...

1994 Eagle Vision [ 1 Answers ]

Hi, I have a 94 eagle vision that just quit while driving. It has been dying at stop signs, but it usually starts right up. This time it won't start. Does anybody know what might be wrong. Thanks Melonman

I've got this limp... [ 10 Answers ]

When our lawn mower broke and wouldn't run, my wife kept hinting to me that I should get it fixed. But, somehow I always had something else to take care of first...always something more important to me. Finally she thought of a clever way to make her point. When I arrived home one day, I...

95 Eagle Vision Doesn't Start Sometimes... [ 1 Answers ]

We have a 95 Eagle Vision that won't start sometimes and dies while we're driving occasionally. It's not the battery or starter or fuel pump. We've had a mechanic look at it, and he thinks he's narrowed it down to one of three different sensors (or perhaps the whole computer), but doesn't know...

View more Cars & Trucks questions Search