Search:
Type: Posts; User: J Costa
Search:
Search took 0.00 seconds.
-
Very good answer flying blue eagle
-
eschuen is correct it does take time but the split will tell you if it is working properly or not it should be about a 18 to 20 degree split any lower or a lot higher should be looked at.
-
Is your fan outside staying on also or just the compressor if both are staying on then you might want to check your contactor outside it may be stuck pulling in there is a button in the middle of the...
-
-
You'll have to drain the water heater but first shut the power off at the breaker so you don't blow your elements if this is electric lift the relief valve when draining it then just replace the...
-
Is this a direct drive or belt drive if it is belt driven check for a broken belt first and post back if it is a direct drive then check the pump and also check the timer sometimes these machines...
-
You might have a worn belt or belts
-
If it works sometimes it is probably not your timer it might be the solenoids themselves going bad.
-
The selector button is bad it is not enguaging properly
-
Try insulating your ductwork
-
If your furnace fan is working you might not be getting power to your heat elements this can be hard to diagnose by yourself if you have a volt meter you can check the points that attach to the...
-
You might be able to get a hold of customer service and or go online and look up the schematic for the door.
-
Does it drain or spin do you hear a humming noise after it fills? It could be a broken belt bad motor see if it will do anything with no load in the washer that could narrow it down also.
-
What do you mean by unclog the drain line, or what?
-
It sounds to me like you have a cooling problem but I am a little confused did it make ice again or did you just get water if the first time water came out your ice that was in there could have...
-
First of all that is the wrong thing to do is to turn it all the way up you need to look at a couple of things you need to check to see if the fan in the back of fridge is working and the compressor...
-
There are many possibilities to this problem first check your lint catcher and clen out the vent tube see if that helps and post back if I do not get to you fast enough there are plenty of people on...
-
Shut your water off to that line and disconnect the line and see if it is clogged sometimes just tapping the valve underneath the dishwasher will unclog it if that does not work take the two leads...
-
I agree with the above answer
-
Yes if you have a continuity tester or multimeter you can take the wires off the button it works like a switch just put your leads on the two terminals it sf it shows good continuity with the button...
-
That is where your evap fan is it might have came loose or the back wall out of alighnment or as xenosapian stated it could have ice building up in there and hitting the fan
-
You need to test it you will need an ohm meter first unplug your appliance then gain access to your element take the two leads off and put your test leads from meter on the terminals if it shows...
-
Did you check your thermastat?
-
It usually is not recommended to close off regiters because that messes with air circulation. I am not familiar with the term gas pack but in air conditioning it is a no-no.
-
To take off the arm you may have to turn it as you would normally be tightening it.
-
You can ohm your element out if you don't get any resistance than it needs to be replaced be sure to unplug at least one of the terminals. If you are trying to acces it you can get a schematic online...
-
It wasn't the thermastat It ended up I took the ice maker out and ohmed out the heater and the motor and the motor is bad which is supprising.
-
-
You can go to the kenmore website and get the manual, just have the model
# ready.
-
The control settings are usually the higher the number the colder the setting
-
It could be a loose wiring connection at the thermastat or the thermastat is faulty put the fan in auto and take a voltage reading from red to green if there is no voltage then it is closed and...
-
Well once the washer is filled up it does not use anymore water from the faucet until it drains so that would not affect the washing cycle from not working.
-
I have a whirlpool side by side refrigerator the ice mker stopped working there was ice froze in there but will not drop I took off the ice maker and got all the ice out it was a solid block I put...
-
You could bypass the limit switch to see if that is the problem shut down all power to furnace take the wires off the limit switch get yourself a piece of wire and connect one end of the wire to one...
-
There are a couple of things you could look for you may have a split drain trough or your door gasket may not be sealing properly you may also check your baffle and make sure it is adjusted properly.
-
First try lowering your setting and give that about 24 hours for your fridge to adjust if it still freezes you probably have a defective cold control.
-
If your unit is heating fine than it is probably not your thermastats blue or orange wiring the blue is typically used toenergize the valve in heat and the orange to energize during cool mode you are...
-
Just received fridge today and the light in fridge side and all display lights not working light switch checks out OK but when I repeatedly hit the switch the filter display will blink changed light...
-
You should have a common wire inside the air handler find what color they are using in there and if you don't have any extra wires behind the thermastat then you will have to run one from the air...
-
So are you saying the outside unit is running but the inside is not
-
No it is a duraguard board for either staight cool or heat pump install
-
Hi guys quick question what is the terminals on the circuit boards marked m1 and m2?
-
first is that the airhandler or condensing unit outside It is hard to tell tonnage on the airhandler but if you have the model number of the outside unit that can easily be translated if numbers are...
-
I agree with esquire usually if things start freezing it is usually the cold control
-
You could also try seeing if there is a lot of dirt built up on the blower and fan blades or squirrel cage.
-
Is it just the outside unit that will not turn off or is it the fan inside also you really did not specify if it is both not turning off look at your thermastat to be your problem if it is just out...
-
If Iam understsnding you correctly you say there is no heat when you turn it on but it just stays cold in your house then when you turn it off it will not the fan will not turn off. Yes the auto and...
-
Thank you for all your help I have it up and running. I appreciate you getting back with me. I ended up wiring it red to red tied in with the float switch in the circuit, the brown common to the blue...
-
Yes The Transformer Was In The Air Handler
-
I have a heat pump outside the way they had the old airhandler wired to it is as follows green to green to fan relay red to red common from relay to outside, white of therm with black off therm with...
|