Ask Experts Questions for FREE Help !
Ask
    dobbsmichelle's Avatar
    dobbsmichelle Posts: 3, Reputation: 1
    New Member
     
    #1

    Dec 13, 2007, 03:29 PM
    Kenmore elite calypso error messages
    I had error message CE today then later the LD... I found it meant it long drain. I unpluged the washer before understanding the message so now it won't drain. How do I reset the brain so that it can drain and work. Every time I go to do any wash cycle it starts and instantly shuts off the water from filling up. I assume because it is full.

    Any ideas on what to do?

    Error messages I received today were LD, 5r, CE. All I did was try to presoak sheets overnight... didn't work.. and know it doesn't work at all... help me please..

    Michelle
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
     
    #2

    Dec 14, 2007, 08:55 PM
    If there is any breakdown in communication between the machine controller and the motor controller, "CE" flashes and the unit beeps once.
    Some common causes of "CE" errors include:
    ·Conformal coating on serial communications pins between the machine controller and motor controller. After disconnecting power to the unit, try scraping this coating off the pins.
    · Check the resistance values between the serial communications pins with the connectors in place. Make sure the harness does not have a bad connection.
    · Check the quick disconnect at the motor terminal. The drive motor must be hooked up properly or a "CE" error will occur.
    · Drive motor thermal protector has opened.
    ·Motor controller is not powered or fuse has opened. Replace motor controller.

    Press STOP/CANCEL to clear the display.
    dobbsmichelle's Avatar
    dobbsmichelle Posts: 3, Reputation: 1
    New Member
     
    #3

    Dec 15, 2007, 08:50 PM
    Now the CE is gone and I keep getting LD... I researched it and it means long drain.. so how long is long because I don't hear it draining at all. I tried to rinse and spin to drain.. but water is not just sitting in the bottom.. any further suggestions?

    I am on day three of a down washer here.. Hhheellppppp
    dobbsmichelle's Avatar
    dobbsmichelle Posts: 3, Reputation: 1
    New Member
     
    #4

    Dec 15, 2007, 08:50 PM
    Oh I get 5r for an error message too.. any ideas?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore elite calypso code ld [ 2 Answers ]

Can anyone tell me how to solve code LD on my kenmore elite calypso washer?it kept stopping.today I had to vacuum the water out.

Anyone with the code book for kenmore calypso elite? [ 1 Answers ]

Hey please help my clothes are smellingwasher isn't working. Shows ld ( long drain and I lost my dance test paper to trouble shoot it) I cleared it once before

Kenmore Elite Calypso - doesn't get clothes clean and just reeks! [ 1 Answers ]

We have a Kenmore Elite Washer with Calypso wash motion, model 110.21062000. It seems to run through all of its normal cycles, but the water that stays in the tub under the basket reeks, like old wet mop rags that have sat too long in a dark place. I mean, my wife made me take it outside reeks. ...

Kenmore Calypso Elite Washer Code cl [ 1 Answers ]

What is code cl?

Kenmore Elite Calypso "ob" error message [ 1 Answers ]

Hi! I can't find my manual on my washer. It's a Kenmore Elite Calypso. It goes through most of the cycle and towards the end I get "ob" error message. I'm thinking it means off balance, but it has been balanced. Any suggestions? Thanks, Bridget


View more questions Search