I have a Nordyne heater which has been working great for the last 4 years. Tonight, however, the blowers are constantly operating even though the thermostat is off. The red indicator light is indicating that the limit circuit is open or there's and external load on "W". which I think refers to the room thermostat. When I set the thermostat, nothing happens- no firing and no heat. The unit was professionally installed and I intend to place a call to a professional tomorrow. However, can anyone tell me if there is something else I should check? Also, besides turning off the circuit breaker, how can I get the blowers to stop? Thanks in advance for any advice.

Turn off at the breaker box to get it to stop completely.

I turned off the circuit breaker but, of course, that also turns off several other things in the house. When I turn the breaker back on, the blower starts almost immediately. Any other ideas? Thanks

there should be a switch near the furnace that will turn power off to furnace only. follow wiring from furnace and see if you can find the shut off. If the furnace is fairly new, you may also be able to take the covers off of the furnace. when you take the bottom cover off of the furnace, it should open a door safety switch which will kill the power to the furnace. Please let me know if this works. If not, turn the breaker off, take a flashlight(assuming turning the breaker off kills the lights in the furnace room) disconnect wires from furnace junction box, wire nut them separately, and turn the breaker back on. Good luck and let me know how things work out.

I turned off the circuit breaker but, of course, that also turns off several other things in the house. When I turn the breaker back on, the blower starts almost immediately. Any other ideas? Thanks


where I come from professional HVAC installers know to put a furnace on a breaker all to itself,,that way when breaker is /needs to be turned off the furnace is all thats turned off,,,,its code,the safe way to do things

I have never been a fan of having multiple loads on a circuit with a furnace.

does the circut board have a fuse in it? small 3 amp automotive type fuse,,if so check it out

the above advice is exactly right. But there are alot of half assers out there, that dont dedicate a furnace to one breaker. Not so much these days, but they used to do it alot, just didnt know any better, most likely lack of training. We just need to help him figure out how to get that furnace shut down, without killing breakers, for now. Hope he can get it done. Then hopefully he will have a true electrician in to straighten out his wiring.

the above advice is exactly right. But there are alot of half assers out there, that dont dedicate a furnace to one breaker. Not so much these days, but they used to do it alot, just didnt know any better, most likely lack of training. We just need to help him figure out how to get that furnace shut down, without killing breakers, for now. Hope he can get it done. Then hopefully he will have a true electrician in to straighten out his wiring.

Electrician? Blasphemy.

wmproop. I let the electricians take care of the power sources(have enough to worry about).lol. although i always thought it would be cool to get my masters in electrical, then i could pull my last three hairs out. just need that little extra stress.

wmproop. I let the electricians take care of the power sources(have enough to worry about).lol. although i always thought it would be cool to get my masters in electrical, then i could pull my last three hairs out. just need that little extra stress.

With the company I work for and the type of work I mainly do (commercial refrigeration) I have to be an HCAV/R tech, an electrician and a plumber. :p

Mark... Yep electrician. They have families to feed to. There is a reason they have the trade they do. Im not a licensed electician. Therefore my insurance doesnt cover me doing electrical work. Of course i do simple electrics(wouldnt call an electrcian to work on a furnace. or trouble shoot a thermostat, most wouldnt know where to start) but when it comes to dedicated lines, with proper wire sizing from the breaker panel, I leave it up to them.

When I was in HVAC/R school the very first course we were required to take was electricity and electrical theory. This included residential wiring.

in my state and I thought most other states,in order to be a HVAC contractor we all have to carry a speciality HVAC/plumbing electricians card saying we are trained and able to do our own wiring for hvac/plumbing only,,,,it cost me 50 bucks a year to carry the card,,,:)

I agree again Mark. In our trade/trades, we have to be able to do a little of everything. But there is a line to be drawn. We spend years in training, usually for one specific field. During this time, we learn about many fields. But we only get licensed for one. Im betting you are an awesome HVAC-R tech, but i most likely wouldnt have you replumb my house.LOL.

In my state, i would be old enough to retire by the time i went though all the apprenticeships , journeyman, master levels to aquire plumbing and electrical. Have a five year apprenticeship for both plumbing and electrical, and another five after that before you can take your masters. Have to have a masters here before you can own your own business. So to be a master plumber and electrician, it would 18 to twenty years. Like i said, I dont need the extra stress. lol

PS. Yes i live in a very very strict state. dont even get me started on fire sprinkler systems, that just adds more years.

as far as I know the HVAC/plumbing electricians card only allows us to plumb gas lines to HVAC equipment and hot water heaters,,,,,plumbing and electrical wiring,,,but we did have to take schooling and a state test.

correct wmproop. As a licensed plumber, and hvac-r tech, i am allowed to run gas and to do local electrical connection( hook up water heater, furnaces, ac units, etc,) just not allowed to run wires from main panel and such.
Not that i havent had to, just wouldnt want the electrical inspector to stop by while i doing it.

Thanks to everyone for their advice. I found the switch and turned the heater off; I'll contact a local professional to check it out. Until then...brrrrrr.

Here in Indiana we aren't required to carry an additional card. In addition, when applying for a residential building permit in my town the only permit you cannot get is plumbing, the rest you can test out of. But then again I also live in a state where there are no seat belt laws if you are driving a pick-up truck.

Kind of makes you wonder how UNITED our states really are. Maybe they should just let us actuall workers draw up the rules and make them the same throughout the entire united states. Of course, we would be to busy working our bottoms off to accomplish this task. That would make us paper pushers instead or workers.lol.