Ask Experts Questions for FREE Help !
Ask
    dm1's Avatar
    dm1 Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Oct 14, 2006, 05:07 PM
    Bryant furnace won't lite
    Hello,

    I have a Bryant furnace. It Keeps flashing code 13 on the circuit board. I read the code and it says that the switch will reset after 3 hours. It also refers me to # 33 which gives more possibilities as to what the problem may be. However it does say to reset the limit or flame roll out switch manually or replace the fuse link. I also took the ignitor and had it tested and it checks out OK.

    I would like to know how to manually reset the limit or flame roll out switch and or replace the fuse link. I also would need to know what the fuse link looks like. I know what the flame roll out switch looks like but I do not know what the limit switch looks like either. I checked all of the other possibilities and have narrowed it down to this one.

    Can anyone help?

    Thanks
    dm1
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #2

    Oct 14, 2006, 08:19 PM
    Main limits are self resetting and part should be replaced. Roll out limits have a small button on top between the two wires, just gently push the button down until it clicks. Why did a roll out trip? This could be a real safety issue.
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
    		  
    #3

    Oct 14, 2006, 09:05 PM
    I am sure that by now your 3 hour wait for the circuit board to reset has passed. So tell us what the furnace is doing now, I am sure someone will be able to help you.
    bieleckiap's Avatar
    bieleckiap Posts: 1, Reputation: 1
    New Member
    		  
    #4

    Dec 22, 2006, 09:28 PM
    Hi dm1
    I was wonder how did you fix your furnace. I had perfectly fine one until I left for pre-X-mass vacation. I left it on at 50F and the house was at 52F but when I come back after 6 days and try to light it up to 72F only fan was working. I'm getting 3 fast and one long which I think is code 13. Since it's late Friday looks like I won't be able to find someone before Tuesday which means long and cold X_mass. It's sucks. I'm not sure if my rollout switch is on or off since pin is out and the thicker part on the switch is like only 1/16 out of the body of the switch and I can't push it in and I'm scared maybe this is not the switch and I will just break it.

    Thanks for any help
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Bryant furnace problem [ 20 Answers ]

Hi All, I have a 5 y/o 80% eff bryant furnace. The problem I have is that my furnace Doesn't always kick on even when thew thermostat shows the temp under the Temp set. I will sometimes have to go down and turn of the blower switch on the furnace wait a couple seconds and then turn it on again....

Lite On Combo Drive [ 1 Answers ]

Having trouble finding the drivers for a Lite On Combo LTC-48161H dvd/rw drive.According to various Googling I've done,the driver download sites on the net,are either incomprehensible,or don't work.Even the manufacturers site does a 404! In other words,as things stand,the combo-drive does zip,and...

New Bryant A/C compessor will not run [ 1 Answers ]

I have a newly installed Bryant 2 1/2 ton compressor unit that was installed in August 2005. When I turned on the A/C the unit would not start. I checked the disconnect near the compressor and found it to be faulty and replaced it with a new one and there is still no start up. I pulled the panel to...

Faulty lite [ 3 Answers ]

:confused: I recently installed a flouresent lite fixture and after being on for ten or fifteen minutes, it shuts off. Is the ballast bad or something else going on? Thank-jb.

Gas Furnace Doesn't Lite [ 3 Answers ]

My Carrier Furnace Igniter glows but the valve won't turn the gas on. I have discovered that the relay switch on the top of the valve has a bad connection to the pins (2 each) on the two solenoids. I can loosen this and slide up and down several times and it will work for awhile. My problem is that...

View more questions Search